Difficulty

Very difficult

Steps

29

Time Required

                          45 minutes - 2 hours

Sections

5

  • Battery
  • 3 steps
  • Circle Pad Joystick
  • 8 steps
  • IR Board
  • 1 step
  • Motherboard
  • 10 steps
  • Upper LCD
  • 7 steps

Flags

0

  • Back3DS XL

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Loosen the two 4.2 mm-length screws located at the top of the back cover.
  • The screws have locking washers that prevent the screws from falling off of the back cover. Leave these locking washers on the screws; it is not necessary to remove the washers for this repair guide.

Loosen the two 4.2 mm-length screws located at the top of the back cover.

The screws have locking washers that prevent the screws from falling off of the back cover. Leave these locking washers on the screws; it is not necessary to remove the washers for this repair guide.

1024

Step 2

  • Hold the device so that the cover is facing up.
  • Using a plastic opening tool, pry off the cover starting at the top right corner.
  • Hold the edge of the cover to ensure it does not reattach.
  • Look for the small section below the stylus compartment. Pry off the cover at that point if it is still attached.
  • Take off the cover of the device and set it aside.

Hold the device so that the cover is facing up.

Using a plastic opening tool, pry off the cover starting at the top right corner.

Hold the edge of the cover to ensure it does not reattach.

Look for the small section below the stylus compartment. Pry off the cover at that point if it is still attached.

Take off the cover of the device and set it aside.

Step 3

  • Insert the plastic opening tool into the opening located on the right side of the battery.
  • Pry off the battery from the lower casing.
  • Lift the battery out of the case and set aside.

Insert the plastic opening tool into the opening located on the right side of the battery.

Pry off the battery from the lower casing.

Lift the battery out of the case and set aside.

Step 4

              Circle Pad Joystick
  • Using tweezers pull out the rubber bumpers that are located at the top of the device on either side of the game cartridge compartment.

Using tweezers pull out the rubber bumpers that are located at the top of the device on either side of the game cartridge compartment.

Step 5

  • Remove the six 6.2 mm screws using a Phillips #00 screwdriver

Remove the six 6.2 mm screws using a Phillips #00 screwdriver

Step 6

  • Remove the 2.3 mm screw located above the game cartridge slot with a Phillips #00 screwdriver.

Remove the 2.3 mm screw located above the game cartridge slot with a Phillips #00 screwdriver.

Step 7

  • Make sure the SD card has been removed. With a plastic opening tool pry off the lower case starting at the bottom edge and working around the perimeter.
  • Two ribbon cables connect the case to the circuit board. Be careful to not pull the case too hard and rip the ribbon cables.

Make sure the SD card has been removed. With a plastic opening tool pry off the lower case starting at the bottom edge and working around the perimeter.

Two ribbon cables connect the case to the circuit board. Be careful to not pull the case too hard and rip the ribbon cables.

Step 8

  • Remove the ribbon cables located underneath the left and right bumpers by prying up the base of the cables with a plastic opening tool.
  • Completely remove the lower case from the rest of the device and set aside.

Remove the ribbon cables located underneath the left and right bumpers by prying up the base of the cables with a plastic opening tool.

Completely remove the lower case from the rest of the device and set aside.

Step 9

  • Position the device such that the game cartridge slot is located at the top.
  • Locate the circle pad on the right side of the device.
  • Remove the two 7.5 mm screws on the upper left and the bottom right corners.

Position the device such that the game cartridge slot is located at the top.

Locate the circle pad on the right side of the device.

Remove the two 7.5 mm screws on the upper left and the bottom right corners.

Step 10

  • Using a plastic opening tool pop off the circle pad joystick.
  • Do not use excessive force with the plastic opening tool. There is a ribbon attaching the circle pad joystick to the motherboard that will remain attached.
  • There is a loose washer located in between the circle pad joystick and the circle pad. Use caution and do not lose this piece.

Using a plastic opening tool pop off the circle pad joystick.

Do not use excessive force with the plastic opening tool. There is a ribbon attaching the circle pad joystick to the motherboard that will remain attached.

There is a loose washer located in between the circle pad joystick and the circle pad. Use caution and do not lose this piece.

Step 11

  • Using the flat head side of the spudger carefully lift up the retaining flap that attaches the circle pad ribbon to the motherboard.
  • Remove the ribbon and circle pad joystick.

Using the flat head side of the spudger carefully lift up the retaining flap that attaches the circle pad ribbon to the motherboard.

Remove the ribbon and circle pad joystick.

Step 12

              IR Board
  • Position the device such that the game cartridge slot is located at the top.
  • Locate the IR board located on the upper right side of the motherboard.
  • The IR board is installed upside-down in these photos by mistake. Installing it this way will result in your DS failing to start. Note the orientation of your IR board before you remove it, and reinstall it the same way.
  • Remove the IR board with a plastic opening tool by inserting the tool below the IR board and gently prying up.

Locate the IR board located on the upper right side of the motherboard.

The IR board is installed upside-down in these photos by mistake. Installing it this way will result in your DS failing to start. Note the orientation of your IR board before you remove it, and reinstall it the same way.

Remove the IR board with a plastic opening tool by inserting the tool below the IR board and gently prying up.

Step 13

              Motherboard
  • Using a plastic opening tool, pry off the Wi-Fi board.
  • The Wi-Fi board will still be connected by a wire and it is not necessary to completely remove it for this step. Simply place it out of the way for this step.

Using a plastic opening tool, pry off the Wi-Fi board.

The Wi-Fi board will still be connected by a wire and it is not necessary to completely remove it for this step. Simply place it out of the way for this step.

Step 14

  • Locate the volume switch on the right side of the motherboard next to the circle pad joystick.
  • Using tweezers, carefully remove the volume board from the casing. It will still be attached to the motherboard by a ribbon cable.

Locate the volume switch on the right side of the motherboard next to the circle pad joystick.

Using tweezers, carefully remove the volume board from the casing. It will still be attached to the motherboard by a ribbon cable.

Step 15

  • Using the flat head side of the spudger carefully lift up the flap that attaches the volume board ribbon to the motherboard.
  • Remove the volume board and set aside.

Using the flat head side of the spudger carefully lift up the flap that attaches the volume board ribbon to the motherboard.

Remove the volume board and set aside.

Step 16

  • Remove the black plastic pieces from the lower left and right hand corners with either your fingers or tweezers.
  • You can also remove these pieces easily by carefully lifting up the 3DS and holding it upside-down. They normally fall right out, but don’t lose them!

Remove the black plastic pieces from the lower left and right hand corners with either your fingers or tweezers.

You can also remove these pieces easily by carefully lifting up the 3DS and holding it upside-down. They normally fall right out, but don’t lose them!

Step 17

  • Using the flat head side of the spudger carefully lift up the flap that attaches the two smaller ribbons to the motherboard.
  • These flaps are located on the top right and bottom right side of the motherboard.
  • Remove the ribbons from the flap.

Using the flat head side of the spudger carefully lift up the flap that attaches the two smaller ribbons to the motherboard.

These flaps are located on the top right and bottom right side of the motherboard.

Remove the ribbons from the flap.

Step 18

  • Using the flat head side of the spudger carefully lift up the flaps that attach the wider ribbons to the motherboard.
  • For the wider ribbons make sure to lift the flaps from the white side.
  • Remove the ribbons from the opened flaps.

Using the flat head side of the spudger carefully lift up the flaps that attach the wider ribbons to the motherboard.

For the wider ribbons make sure to lift the flaps from the white side.

Remove the ribbons from the opened flaps.

Step 19

  • Using the flat head side of the spudger carefully lift up the flap that attaches the ribbon to the motherboard.
  • For this flap lift from the black side.
  • Remove the ribbon from the flap.
  • Reassembly: This wide ribbon is the one with the BLACK STRIPE and goes on the upper (visible) side of the motherboard during reassembly.

Using the flat head side of the spudger carefully lift up the flap that attaches the ribbon to the motherboard.

For this flap lift from the black side.

Remove the ribbon from the flap.

Reassembly: This wide ribbon is the one with the BLACK STRIPE and goes on the upper (visible) side of the motherboard during reassembly.

Step 20

  • Remove ten 5.5 mm screws that are located around the face of the motherboard.

Remove ten 5.5 mm screws that are located around the face of the motherboard.

Step 21

  • The motherboard will still be attached at the top right hand corner so do not completely detach it at this point.
  • Carefully lift the board straight up just enough to clear the two plastic mounts located near the top corners of the cartridge slot.
  • Gently flip the motherboard over the top side.

The motherboard will still be attached at the top right hand corner so do not completely detach it at this point.

Carefully lift the board straight up just enough to clear the two plastic mounts located near the top corners of the cartridge slot.

Gently flip the motherboard over the top side.

Step 22

  • Using the flat head side of the spudger carefully lift up the flap that attaches the wider ribbon on the upper right side to the motherboard.
  • Make sure to lift the flap from the white side.
  • Remove the ribbon from the opened flap.
  • Set the motherboard aside.

Using the flat head side of the spudger carefully lift up the flap that attaches the wider ribbon on the upper right side to the motherboard.

Make sure to lift the flap from the white side.

Remove the ribbon from the opened flap.

Set the motherboard aside.

Step 23

              Upper LCD
  • Open the device such that the upper LCD is on top.
  • Using tweezers remove the four rubber pieces that are in all four corners.

Open the device such that the upper LCD is on top.

Using tweezers remove the four rubber pieces that are in all four corners.

Step 24

  • Remove the four 4.3 mm screws located underneath the four rubber pieces with a Phillips #00 screwdriver head.

Remove the four 4.3 mm screws located underneath the four rubber pieces with a Phillips #00 screwdriver head.

Step 25

  • Flip over the device and close the hinge.
  • Position your fingers at the top of the hinge and push downwards in order to push the cover downwards away from the hinge. It only moves 2mm (1/8").

Flip over the device and close the hinge.

Position your fingers at the top of the hinge and push downwards in order to push the cover downwards away from the hinge. It only moves 2mm (1/8").

Step 26

  • Once the top case is loose and unclipped, remove it from the DS.

Once the top case is loose and unclipped, remove it from the DS.

Step 27

  • Remove the screw that is holding 3D mechanism toggle button in place.
  • Carefully pull off the ribbons that connect the camera and speakers to the Upper LCD.
  • The ribbons are attached with adhesives so take caution while removing.

Remove the screw that is holding 3D mechanism toggle button in place.

Carefully pull off the ribbons that connect the camera and speakers to the Upper LCD.

The ribbons are attached with adhesives so take caution while removing.

Step 28

  • Remove the two small ribbons located on the upper left corner.
  • Using a spudger lift up the black hinges that connect the ribbons to the bracket.
  • Pull the ribbons out of the bracket.

Remove the two small ribbons located on the upper left corner.

Using a spudger lift up the black hinges that connect the ribbons to the bracket.

Pull the ribbons out of the bracket.

Step 29

  • Open the hinge and carefully pop off the Upper LCD using your fingers.
  • Gently remove the ribbon from the hinge.
  • Though not required, the task of removing the ribbon cables becomes much easier once you remove the hinge barrel on the right side of the device.
  • Do not lose the tiny fabric and rubber water-resistant rectangles that cover the two speakers; they often fall out once the speakers are removed.
  • The screen’s cover glass can be replaced or transferred to your new screen. The cover is easily scratched by metal tools; use plastic or your fingernail to separate it.
  • Adhere the cover to the new screen by using thin adhesive around the edges, or by reusing the old adhesive.
  • To reinsert the hinge piece, open the console to the last click before it’s completely flat.

Open the hinge and carefully pop off the Upper LCD using your fingers.

Gently remove the ribbon from the hinge.

Though not required, the task of removing the ribbon cables becomes much easier once you remove the hinge barrel on the right side of the device.

Do not lose the tiny fabric and rubber water-resistant rectangles that cover the two speakers; they often fall out once the speakers are removed.

The screen’s cover glass can be replaced or transferred to your new screen. The cover is easily scratched by metal tools; use plastic or your fingernail to separate it.

Adhere the cover to the new screen by using thin adhesive around the edges, or by reusing the old adhesive.

To reinsert the hinge piece, open the console to the last click before it’s completely flat.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      136 other people completed this guide.

Author

                                      with 11 other contributors 


                    Charlene Donlon

Member since: 04/08/2014

9,720 Reputation

                                      8 Guides authored                  



                       Badges:
                       15







                                                        +12 more badges

Team

                       Cal Poly, Team 9-13, Regan Spring 2014                        

                                                  Member of Cal Poly, Team 9-13, Regan Spring 2014 



                    CPSU-REGAN-S14S9G13                     


                                            5 Members                     


                                            43 Guides authored

Timothy Levonius - Oct 31, 2014

Reply

Any good ways to get the ribbon cable back through the hole?

David Mancini - Nov 20, 2014

did u find a solution?? i need help.

Stephen Hernandez - Feb 9, 2015

Carefully just have a pre-twist to it….good luck

justjustintuber - Mar 9, 2015

Note: If your top or bottom screen was working before disassembly and doesn’t work after reassembly, then it’s likely that the connector is loose or dirty or damaged or not clipped or PLACED UPSIDE-DOWN. I had this issue with my Super3DS XL(2015) and it turns out that the reason why my top screen wasn’t working after put together, was because I had the top LCD connector upside-down. After I correctly put the connector in, It worked again! :)

Jesse James Cantu - Jul 10, 2017

Try a Bobby hair pin.