Nintendo 3Ds Xl Ir Board Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 minutes

Sections

Battery
3 steps
Circle Pad Joystick
8 steps
IR Board
1 step

Flags

Back3DS XL
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Loosen the two 4.2 mm-length screws located at the top of the back cover.
The screws have locking washers that prevent the screws from falling off of the back cover. Leave these locking washers on the screws; it is not necessary to remove the washers for this repair guide.

Loosen the two 4.2 mm-length screws located at the top of the back cover.

The screws have locking washers that prevent the screws from falling off of the back cover. Leave these locking washers on the screws; it is not necessary to remove the washers for this repair guide.

1024

Step 2

Hold the device so that the cover is facing up.
Using a plastic opening tool, pry off the cover starting at the top right corner.
Hold the edge of the cover to ensure it does not reattach.
Look for the small section below the stylus compartment. Pry off the cover at that point if it is still attached.
Take off the cover of the device and set it aside.

Hold the device so that the cover is facing up.

Using a plastic opening tool, pry off the cover starting at the top right corner.

Hold the edge of the cover to ensure it does not reattach.

Look for the small section below the stylus compartment. Pry off the cover at that point if it is still attached.

Take off the cover of the device and set it aside.

Step 3

Insert the plastic opening tool into the opening located on the right side of the battery.
Pry off the battery from the lower casing.
Lift the battery out of the case and set aside.

Insert the plastic opening tool into the opening located on the right side of the battery.

Pry off the battery from the lower casing.

Lift the battery out of the case and set aside.

Step 4

              Circle Pad Joystick

Using tweezers pull out the rubber bumpers that are located at the top of the device on either side of the game cartridge compartment.

Using tweezers pull out the rubber bumpers that are located at the top of the device on either side of the game cartridge compartment.

Step 5

Remove the six 6.2 mm screws using a Phillips #00 screwdriver

Remove the six 6.2 mm screws using a Phillips #00 screwdriver

Step 6

Remove the 2.3 mm screw located above the game cartridge slot with a Phillips #00 screwdriver.

Remove the 2.3 mm screw located above the game cartridge slot with a Phillips #00 screwdriver.

Step 7

Make sure the SD card has been removed. With a plastic opening tool pry off the lower case starting at the bottom edge and working around the perimeter.
Two ribbon cables connect the case to the circuit board. Be careful to not pull the case too hard and rip the ribbon cables.

Make sure the SD card has been removed. With a plastic opening tool pry off the lower case starting at the bottom edge and working around the perimeter.

Two ribbon cables connect the case to the circuit board. Be careful to not pull the case too hard and rip the ribbon cables.

Step 8

Remove the ribbon cables located underneath the left and right bumpers by prying up the base of the cables with a plastic opening tool.
Completely remove the lower case from the rest of the device and set aside.

Remove the ribbon cables located underneath the left and right bumpers by prying up the base of the cables with a plastic opening tool.

Completely remove the lower case from the rest of the device and set aside.

Step 9

Position the device such that the game cartridge slot is located at the top.
Locate the circle pad on the right side of the device.
Remove the two 7.5 mm screws on the upper left and the bottom right corners.

Position the device such that the game cartridge slot is located at the top.

Locate the circle pad on the right side of the device.

Remove the two 7.5 mm screws on the upper left and the bottom right corners.

Step 10

Using a plastic opening tool pop off the circle pad joystick.
Do not use excessive force with the plastic opening tool. There is a ribbon attaching the circle pad joystick to the motherboard that will remain attached.
There is a loose washer located in between the circle pad joystick and the circle pad. Use caution and do not lose this piece.

Using a plastic opening tool pop off the circle pad joystick.

Do not use excessive force with the plastic opening tool. There is a ribbon attaching the circle pad joystick to the motherboard that will remain attached.

There is a loose washer located in between the circle pad joystick and the circle pad. Use caution and do not lose this piece.

Step 11

Using the flat head side of the spudger carefully lift up the retaining flap that attaches the circle pad ribbon to the motherboard.
Remove the ribbon and circle pad joystick.

Using the flat head side of the spudger carefully lift up the retaining flap that attaches the circle pad ribbon to the motherboard.

Remove the ribbon and circle pad joystick.

Step 12

              IR Board

Position the device such that the game cartridge slot is located at the top.
Locate the IR board located on the upper right side of the motherboard.
The IR board is installed upside-down in these photos by mistake. Installing it this way will result in your DS failing to start. Note the orientation of your IR board before you remove it, and reinstall it the same way.
Remove the IR board with a plastic opening tool by inserting the tool below the IR board and gently prying up.

Locate the IR board located on the upper right side of the motherboard.

The IR board is installed upside-down in these photos by mistake. Installing it this way will result in your DS failing to start. Note the orientation of your IR board before you remove it, and reinstall it the same way.

Remove the IR board with a plastic opening tool by inserting the tool below the IR board and gently prying up.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      11 other people completed this guide.

Author

                                      with 5 other contributors

                    Charlene Donlon

Member since: 04/08/2014

9,720 Reputation

                                      8 Guides authored                  



                       Badges:
                       15







                                                        +12 more badges

Team

                       Cal Poly, Team 9-13, Regan Spring 2014                        

                                                  Member of Cal Poly, Team 9-13, Regan Spring 2014 



                    CPSU-REGAN-S14S9G13                     


                                            5 Members                     


                                            43 Guides authored

Tony The Tiger - Feb 10, 2015

This guide was really helpful, I had to teardown my 3DS to remove a rice crispy that was stuck in the SD card reader, I don’t know how it got there, I wasn’t even eating cereals

8bitlooser - Dec 18, 2016

was removing the analog stick really necessary?

AppleTopic - May 14, 2022

So I have an original 3DS and a 3DS XL the 3DS Xl Works great but the 3DS won’t turn on. I believe it is because I t has a missing IR Board. I am hoping to use the one on the 3DS XL. Do you think it will work?they look similar in the pictures….. Anyway I am confused as to why I have to take out the cirlepad??

Introduction#

What you need#

Team#

Introduction

What you need

Team