Difficulty

Easy

Steps

3

Time Required

                          5 - 35 seconds

Sections

1

  • Battery
  • 3 steps

Flags

0

  • Back3DS XL

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Loosen the two 4.2 mm-length screws located at the top of the back cover.
  • The screws have locking washers that prevent the screws from falling off of the back cover. Leave these locking washers on the screws; it is not necessary to remove the washers for this repair guide.

Loosen the two 4.2 mm-length screws located at the top of the back cover.

The screws have locking washers that prevent the screws from falling off of the back cover. Leave these locking washers on the screws; it is not necessary to remove the washers for this repair guide.

1024

Step 2

  • Hold the device so that the cover is facing up.
  • Using a plastic opening tool, pry off the cover starting at the top right corner.
  • Hold the edge of the cover to ensure it does not reattach.
  • Look for the small section below the stylus compartment. Pry off the cover at that point if it is still attached.
  • Take off the cover of the device and set it aside.

Hold the device so that the cover is facing up.

Using a plastic opening tool, pry off the cover starting at the top right corner.

Hold the edge of the cover to ensure it does not reattach.

Look for the small section below the stylus compartment. Pry off the cover at that point if it is still attached.

Take off the cover of the device and set it aside.

Step 3

  • Insert the plastic opening tool into the opening located on the right side of the battery.
  • Pry off the battery from the lower casing.
  • Lift the battery out of the case and set aside.

Insert the plastic opening tool into the opening located on the right side of the battery.

Pry off the battery from the lower casing.

Lift the battery out of the case and set aside.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      34 other people completed this guide.

Author

                                      with 9 other contributors 


                    Charlene Donlon

Member since: 04/08/2014

9,720 Reputation

                                      8 Guides authored                  



                       Badges:
                       15







                                                        +12 more badges

Team

                       Cal Poly, Team 9-13, Regan Spring 2014                        

                                                  Member of Cal Poly, Team 9-13, Regan Spring 2014 



                    CPSU-REGAN-S14S9G13                     


                                            5 Members                     


                                            43 Guides authored

Tommy Lynch - Jun 29, 2016

Reply

Time estimate: 3 - 9 hours Difficulty: Very difficult ??????

More like 30-90 seconds, and that’s if you have to search for a screwdriver.

doanaruto - Dec 5, 2017

Reply

机器无法开机怎么办？是电池的问题吗？

Cole Jackson - Mar 21, 2019

Reply

It should be noted that the bottom three clips on the bottom of the backplate can’t just be snapped in, they need to be slipped in, so when removing the backplate, it should be tiled away from the system and then pulled up from the bottom, and those three clips on the bottom should be the first clips in when you’re putting it back together, sliding them in with the backplate at an angle, and then the rest of the clips just snap in.

James Crawford - Aug 28, 2022

Nice tip. Ty.

Scott Vogel - Jun 11, 2021

Reply

Just did this. For reasmbly I recommend putting the bottom/lower part of the case on first before you screw it back on.