Nintendo 3Ds Xl 2015 Motherboard Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          10 - 15 minutes

Sections

Battery
4 steps
Motherboard
11 steps

Flags

Featured Student Guide

This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.

BackNew 3DS XL
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Ensure your device is powered off before proceeding. Failure to do so may result in electrical shock or damage to the device.
Place the 3DS upside down. Remove the game card, headphones, charging cable, stylus, or anything else that may be connected to the device.

Ensure your device is powered off before proceeding. Failure to do so may result in electrical shock or damage to the device.

Place the 3DS upside down. Remove the game card, headphones, charging cable, stylus, or anything else that may be connected to the device.

1024

Step 2

Using a JIS #0 screwdriver, loosen the two black screws on the back.
The screws are held in place by captive washers and should not be completely removed.

Using a JIS #0 screwdriver, loosen the two black screws on the back.

The screws are held in place by captive washers and should not be completely removed.

Step 3

Once the screws are loosened, pry open the back cover.

Once the screws are loosened, pry open the back cover.

Step 4

The battery is located on the left hand side of the 3DS - to remove, use the small gap located at the top-middle and pull up with a pointed tool.

The battery is located on the left hand side of the 3DS - to remove, use the small gap located at the top-middle and pull up with a pointed tool.

Step 5

              Motherboard

Using a JIS #000 screwdriver, remove the six 6mm screws around the edges of the secondary cover.

Using a JIS #000 screwdriver, remove the six 6mm screws around the edges of the secondary cover.

Step 6

Using tweezers, carefully pop out the rubber bumpers located at the top side of the 3DS. Removing them will reveal another two 6mm screws. Remove these screws using a JIS #000 as well.

Using tweezers, carefully pop out the rubber bumpers located at the top side of the 3DS. Removing them will reveal another two 6mm screws. Remove these screws using a JIS #000 as well.

Step 7

To separate the cover, carefully lift it up and away from the hinges (in order to clear the headphone port), then pivot it towards the hinges to expose the circuit boards.
Don’t fully remove the cover yet, or you may damage the delicate ribbon cable that still connects it to the motherboard.

To separate the cover, carefully lift it up and away from the hinges (in order to clear the headphone port), then pivot it towards the hinges to expose the circuit boards.

Don’t fully remove the cover yet, or you may damage the delicate ribbon cable that still connects it to the motherboard.

Step 8

Use a pair of tweezers to lift away the two plugs that latch the L/R/ZL/ZR button ribbons to the motherboard. You can now remove the back cover completely and set it aside.

Use a pair of tweezers to lift away the two plugs that latch the L/R/ZL/ZR button ribbons to the motherboard. You can now remove the back cover completely and set it aside.

Step 9

Use tweezers to flip up the small, hinged locking flap in order to unlock the ZIF connector securing the circle pad ribbon.
Slide the ribbon out of the ZIF connector.

Use tweezers to flip up the small, hinged locking flap in order to unlock the ZIF connector securing the circle pad ribbon.

Slide the ribbon out of the ZIF connector.

Step 10

Using a JIS #000 screwdriver, remove the two 8 mm screws securing the circle pad.

Using a JIS #000 screwdriver, remove the two 8 mm screws securing the circle pad.

Step 11

Lift the circle pad casing upward to remove it. There will be some friction, but it should not require excessive force.

Lift the circle pad casing upward to remove it. There will be some friction, but it should not require excessive force.

Step 12

Locate the gold terminal plug with a red cable at the top left of the motherboard. Using your fingers, carefully pull the plug straight upward to remove.
Use a pair of tweezers to disconnect the single ribbon connector.
Don’t do what we did – be very careful not to pull on the red cable.

Locate the gold terminal plug with a red cable at the top left of the motherboard. Using your fingers, carefully pull the plug straight upward to remove.

Use a pair of tweezers to disconnect the single ribbon connector.

Don’t do what we did – be very careful not to pull on the red cable.

Step 13

Using tweezers, gently pull the five marked ribbons out of the ZIF connectors along the sides of the motherboard.
These ZIF connectors are held in place by friction and do not have locks—lifting the flaps on these connectors will break them! Note that in some models the upper-most connector may have a lock.
Three of the ribbon connectors have plastic clamping flaps that cover the ribbon to prevent slippage. Use the tweezers to flip them up before ribbon removal.
When reassembling the device, be sure to flip the ZIF clamps back down.
While the SD card reader is shown as removed in this photo, it is optional for the removal of the motherboard.

Using tweezers, gently pull the five marked ribbons out of the ZIF connectors along the sides of the motherboard.

These ZIF connectors are held in place by friction and do not have locks—lifting the flaps on these connectors will break them! Note that in some models the upper-most connector may have a lock.

Three of the ribbon connectors have plastic clamping flaps that cover the ribbon to prevent slippage. Use the tweezers to flip them up before ribbon removal.

When reassembling the device, be sure to flip the ZIF clamps back down.

While the SD card reader is shown as removed in this photo, it is optional for the removal of the motherboard.

Step 14

Using a JIS #000 screwdriver, remove six 4mm screws along the edges of the motherboard.

Using a JIS #000 screwdriver, remove six 4mm screws along the edges of the motherboard.

Step 15

Carefully pivot the motherboard 90 degrees toward the hinges to reveal two more ZIF connectors on the underside of the motherboard.
Both have latches that must be flipped up. The left, longer latch is black; the right, shorter one is white. Flip up the flaps, slide the ribbons out and remove the motherboard.
Note which way the ribbons slide into their connectors carefully, as they are different.

Carefully pivot the motherboard 90 degrees toward the hinges to reveal two more ZIF connectors on the underside of the motherboard.

Both have latches that must be flipped up. The left, longer latch is black; the right, shorter one is white. Flip up the flaps, slide the ribbons out and remove the motherboard.

Note which way the ribbons slide into their connectors carefully, as they are different.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      43 other people completed this guide.

Author

                                      with 15 other contributors

                    BabblingFishes

Member since: 04/01/2015

1,163 Reputation

                                      1 Guide authored                  



                       Badges:
                       14







                                                        +11 more badges

Team

                       Cal Poly, Team 24-4, Lancaster Spring 2015                        

                                                  Member of Cal Poly, Team 24-4, Lancaster Spring 2015 



                    CPSU-LANCASTER-S15S24G4                     


                                            4 Members                     


                                            20 Guides authored

emaN - Feb 10, 2016

Could someone point out where the fuses in the motherboard are hidden?

BabblingFishes - Feb 11, 2016

With some digging, I managed to find this on the GBAtemp forums , which host a community of 3DS modders:

https://gbatemp.net/threads/screwed-up-p…

Seems like no one’s quite sure, but it could be a start. Unfortunately, the N3DS components are largely small black boxes with no labeling.

If you have a multimeter, it might help to test some of these mystery boxes.

Mijii - Feb 16, 2017

Question: Seeing as how you pulled the red cable in the photos, how was that fixed? Asking for a friend.

BabblingFishes - Feb 17, 2017

We…never fixed that actually, as we didn’t have the tools for it and the device had been loaned to us specifically for tearing down.

I don’t know if iFixit themselves ever did anything with it, but I would imagine soldering the frayed end of the cable back onto the plug would work. (Here’s a guide on that: http://www.instructables.com/id/Solderin… )

isaa sy - May 17, 2017

what version is this on?

Featured Student Guide#

Introduction#

What you need#

Team#

Featured Student Guide

Introduction

What you need

Team