Nintendo 3Ds 2015 Lower Case Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          10 minutes

Sections

Battery
3 steps
SD Card Reader
3 steps
Lower Case
3 steps

Flags

BackNew 3DS 2015
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Unscrew the two 3mm Phillips #0 head screws along the top edge of the device.
The screws on the back panel strip easily. Go slowly and press down firmly.
The screws on the back panel are held in by locking washers, so they won’t come out of the back panel.

Unscrew the two 3mm Phillips #0 head screws along the top edge of the device.

The screws on the back panel strip easily. Go slowly and press down firmly.

The screws on the back panel are held in by locking washers, so they won’t come out of the back panel.

1024

Step 2

Pull the top corner tabs of the front face plate outward and towards you.
Pull the faceplate up and out of the slots at the bottom of the device.
Set aside the back faceplate.

Pull the top corner tabs of the front face plate outward and towards you.

Pull the faceplate up and out of the slots at the bottom of the device.

Set aside the back faceplate.

Step 3

Insert a plastic opening tool into the notch at the top of the battery.
Pry the battery up with the plastic opening tool.

Insert a plastic opening tool into the notch at the top of the battery.

Pry the battery up with the plastic opening tool.

Step 4

              SD Card Reader

Unscrew the three 3mm Y0 screws along the right and bottom of the SD card reader.
The bottom of the SD card reader should slightly pop out after removing the screws.

Unscrew the three 3mm Y0 screws along the right and bottom of the SD card reader.

The bottom of the SD card reader should slightly pop out after removing the screws.

Step 5

Pull the SD card reader from the edge with two holes gently to free the tab at the top of the SD card reader.
Don’t completely pull the SD card out of the device yet. There is a ribbon cable connected under the SD card reader.
Reorient the device so that the power jack faces you.

Pull the SD card reader from the edge with two holes gently to free the tab at the top of the SD card reader.

Don’t completely pull the SD card out of the device yet. There is a ribbon cable connected under the SD card reader.

Reorient the device so that the power jack faces you.

Step 6

Lift the SD card reader gently.
Use a plastic opening tool to pry the SD card ribbon cable off the socket on the motherboard.
Lift the SD card reader out off of the lower casing.

Lift the SD card reader gently.

Use a plastic opening tool to pry the SD card ribbon cable off the socket on the motherboard.

Lift the SD card reader out off of the lower casing.

Step 7

              Lower Case

Reorient the device so that the game slot now faces you.
Remove the two rubber bumpers along the top of the device using tweezers.
Unscrew the seven 6mm Phillips #00 screws along the top and bottom of the 3DS.

Reorient the device so that the game slot now faces you.

Remove the two rubber bumpers along the top of the device using tweezers.

Unscrew the seven 6mm Phillips #00 screws along the top and bottom of the 3DS.

Step 8

Lift the top edge of the lower case slightly off on the 3DS.
Don’t pull the lower casing completely off, you may break those connections. There are ribbon cables that must be disconnected first.
Pry the ribbon cable socket under the right trigger using a plastic opening tool.
Pry the ribbon cable socket under the infrared receiver cover using a plastic opening tool.

Lift the top edge of the lower case slightly off on the 3DS.

Don’t pull the lower casing completely off, you may break those connections. There are ribbon cables that must be disconnected first.

Pry the ribbon cable socket under the right trigger using a plastic opening tool.

Pry the ribbon cable socket under the infrared receiver cover using a plastic opening tool.

Step 9

Open the device slowly from its top edge. Be careful not to tug the ribbon cable connected near the bottom edge of the device.
Pry the last ribbon cable attached to the lower case using a plastic opening tool.

Open the device slowly from its top edge. Be careful not to tug the ribbon cable connected near the bottom edge of the device.

Pry the last ribbon cable attached to the lower case using a plastic opening tool.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 3 other contributors

                    Ahmed Gouda

Member since: 10/06/2016

268 Reputation

                                      1 Guide authored                  



                       Badges:
                       12







                                                        +9 more badges

Team

                       Cal Poly, Team 4-6, Livingston Fall 2016                        

                                                  Member of Cal Poly, Team 4-6, Livingston Fall 2016 



                    CPSU-LIVINGSTON-F16S4G6                     


                                            4 Members                     


                                            35 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team