Ninja Professional Blender Bl660 Fan Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          35 - 40 minutes

Sections

Blender Base
5 steps
Fan
3 steps

Flags

BackNinja Professional Blender BL660
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Blender Base

Using the Phillips #1 screwdriver, remove the 5 screws (13mm long, 6mm wide) holding the outer base.
Lift the base up to remove it.

Using the Phillips #1 screwdriver, remove the 5 screws (13mm long, 6mm wide) holding the outer base.

Lift the base up to remove it.

1024

Step 2

Remove the midsection by pulling it up. If the section is stuck, use the iFixit plastic opening tool to pry it off.
Pull the power cord through the mid-section opening.

Remove the midsection by pulling it up. If the section is stuck, use the iFixit plastic opening tool to pry it off.

Pull the power cord through the mid-section opening.

Step 3

Using the Phillips #1 screwdriver, remove the 6 screws (13 mm long, 6 mm wide).

Using the Phillips #1 screwdriver, remove the 6 screws (13 mm long, 6 mm wide).

Step 4

Using the Phillips #1 screwdriver, remove the two screws (5 mm long, 3 mm wide) holding the power cord onto the motor cover.

Using the Phillips #1 screwdriver, remove the two screws (5 mm long, 3 mm wide) holding the power cord onto the motor cover.

Step 5

Using the iFixit plastic opening tool, pry the motor cover off the general housing. Once it is loose, lift it up to remove it off the base.
Slide the cover all the way to the end of the power cord.
Please note that the power cord does not completely come off the cover.

Using the iFixit plastic opening tool, pry the motor cover off the general housing. Once it is loose, lift it up to remove it off the base.

Slide the cover all the way to the end of the power cord.

Please note that the power cord does not completely come off the cover.

Step 6

Fan

Use a wrench or a pair of pliers to help remove the nut on top of the fan. Holding the fan itself will help make the process easier.
The fan blades are sharp. Handle with care. Using a paper towel or cloth while handling is recommended.

Use a wrench or a pair of pliers to help remove the nut on top of the fan. Holding the fan itself will help make the process easier.

The fan blades are sharp. Handle with care. Using a paper towel or cloth while handling is recommended.

Step 7

Use the plastic opening tool to loosen the washer.

Use the plastic opening tool to loosen the washer.

Step 8

Remove washer then slide the fan off the screw.
Replace the fan as needed.
The fan has a keyed hole, thus it fits on the shaft in a specific way. Ensure you put it on correctly.

Remove washer then slide the fan off the screw.

Replace the fan as needed.

The fan has a keyed hole, thus it fits on the shaft in a specific way. Ensure you put it on correctly.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors

                    Mikey Marquiss

Member since: 09/22/2017

213 Reputation

                                      2 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       Central Washington University, Team S1-G1, Pengilly Fall 2017                        

                                                  Member of Central Washington University, Team S1-G1, Pengilly Fall 2017 



                    CWU-PENGILLY-F17S1G1                     


                                            4 Members                     


                                            7 Guides authored

Tania Polanco - Aug 5, 2018

I did that but the other fan is the one that is lock and do not turn on. The white one in the middle. How can I fix it.

Introduction#

What you need#

Team#

Introduction

What you need

Team