Difficulty

Moderate

Steps

7

Time Required

                          15 - 20 minutes

Sections

2

  • Blender Base Cover
  • 3 steps
  • Circuit Board
  • 4 steps

Flags

1

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

  • BackNinja Professional NJ600

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Blender Base Cover
  • Remove the five screws (13mm long, 6mm head diameter) using a Phillips #2 screwdriver.

Remove the five screws (13mm long, 6mm head diameter) using a Phillips #2 screwdriver.

1024

Step 2

  • Without removing any screws, you can pull the 2nd layer free from the base. Do this now and set it down gently next to the base.
  • The power cord runs through a hole in the side of this layer. Squeeze the cord and pull it through the hole to separate the layer from the cord.

Without removing any screws, you can pull the 2nd layer free from the base. Do this now and set it down gently next to the base.

The power cord runs through a hole in the side of this layer. Squeeze the cord and pull it through the hole to separate the layer from the cord.

Step 3

  • Using the Phillips #2 screwdriver, remove these six screws (13mm long, 6mm head diameter). Then carefully remove this layer, and rest it next to the blender base.
  • Be careful not to damage the two wires that are keeping this third layer attached to the base.

Using the Phillips #2 screwdriver, remove these six screws (13mm long, 6mm head diameter). Then carefully remove this layer, and rest it next to the blender base.

Be careful not to damage the two wires that are keeping this third layer attached to the base.

Step 4

              Circuit Board
  • Remove these four screws (10mm long, 5mm head diameter) using a Phillips #2 screwdriver.
  • Be careful not to scratch the circuit board with the screwdriver.

Remove these four screws (10mm long, 5mm head diameter) using a Phillips #2 screwdriver.

Be careful not to scratch the circuit board with the screwdriver.

Step 5

  • Using a pair of scissors or wire cutters, cut the zip tie holding these wires.
  • This will give the circuit board more range of motion.

Using a pair of scissors or wire cutters, cut the zip tie holding these wires.

This will give the circuit board more range of motion.

Step 6

  • Desolder the five wires from the solder pads shown.
  • If you do not know how to do this, iFixit has a guide describing the process.
  • Before you begin to desolder these wires, flip the board over to confirm that you are about to desolder the correct component.
  • Soldering iron is very hot, use caution when handling

Desolder the five wires from the solder pads shown.

If you do not know how to do this, iFixit has a guide describing the process.

Before you begin to desolder these wires, flip the board over to confirm that you are about to desolder the correct component.

Soldering iron is very hot, use caution when handling

Step 7

  • After the wires have cooled enough to touch, carefully slide the circuit board free of the wires.
  • NOTE: keep track of which pad each wire was soldered to. This is important for your blender to function.

After the wires have cooled enough to touch, carefully slide the circuit board free of the wires.

NOTE: keep track of which pad each wire was soldered to. This is important for your blender to function.

To reassemble your device, follow these instructions in reverse order, but solder the wires back to the board.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 4 other contributors 


                    Kody D

Member since: 04/01/2015

513 Reputation

                                      3 Guides authored                  



                       Badges:
                       15







                                                        +12 more badges

Team

                       Cal Poly, Team 24-2, Lancaster Spring 2015                        

                                                  Member of Cal Poly, Team 24-2, Lancaster Spring 2015 



                    CPSU-LANCASTER-S15S24G2                     


                                            4 Members                     


                                            6 Guides authored

Odman - Apr 11, 2016

Reply

Good article. How do I get hold of a board?

carlareis1 - Jun 19, 2016

Reply

Where can I buy de circuito board?

Adesoye Olatunji - Jan 21, 2018

Reply

Where can i buy the circuit board ?

Daniel - Dec 31, 2020

Reply

Hi, where can I buy this board please?