Difficulty
Moderate
Steps
11
Time Required
30 minutes
Sections
3
- Valve Tubes
- 4 steps
- Water Heater
- 6 steps
- Hot Water Tubing
- 1 step
Flags
0
BackNinja Coffee Bar Single-Serve System CF111 30
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Valve Tubes
- Unscrew (8) 6mm screws using Phillips head #1 screwdriver
- Remove bottom cover
Unscrew (8) 6mm screws using Phillips head #1 screwdriver
Remove bottom cover
1024
Step 2
- Unscrew (3) 6mm screws with Phillips head #1 screwdriver
- Remove tube protection plate
Unscrew (3) 6mm screws with Phillips head #1 screwdriver
Remove tube protection plate
Step 3
- Detach valve tubes from valve by squeezing pins and pull tubes away from valve
Detach valve tubes from valve by squeezing pins and pull tubes away from valve
Step 4
- Detach valve tubes from device by pinching pins and sliding the tubes off
Detach valve tubes from device by pinching pins and sliding the tubes off
Step 5
Water Heater
- Unscrew the four 6mm #1 Phillips head screws from the underside of the basket area.
- Remove the single 6mm #1 Phillips-head screw from the side of the unit.
Unscrew the four 6mm #1 Phillips head screws from the underside of the basket area.
Remove the single 6mm #1 Phillips-head screw from the side of the unit.
Step 6
- Slowly pry the upper cover away from the unit on top of the brew basket, and near the base of the water reservoir along the side of the upper cover.
Slowly pry the upper cover away from the unit on top of the brew basket, and near the base of the water reservoir along the side of the upper cover.
Step 7
- Separate hose from upper nozzle by squeezing the clamp and pulling the hose down slightly.
Separate hose from upper nozzle by squeezing the clamp and pulling the hose down slightly.
Step 8
- Using a #1 Phillips head screwdriver with an extension, remove three 6mm screws holding the heater to the unit.
Using a #1 Phillips head screwdriver with an extension, remove three 6mm screws holding the heater to the unit.
Step 9
- Remove heater from unit.
Remove heater from unit.
Step 10
- Squeeze clip and separate signal wiring.
- Using wire stripper/crimping tool, uncrimp wiring connectors
- Wiring connectors are sealed together making them difficult to disconnect. Cutting and rewiring should be considered.
Squeeze clip and separate signal wiring.
Using wire stripper/crimping tool, uncrimp wiring connectors
Wiring connectors are sealed together making them difficult to disconnect. Cutting and rewiring should be considered.
Step 11
Hot Water Tubing
- Squeeze connector and pull tubing away from heater.
- Inspect tubing for damage and/or weak spots and replace if necessary.
Squeeze connector and pull tubing away from heater.
Inspect tubing for damage and/or weak spots and replace if necessary.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Kyle Gustafson
Member since: 11/04/2018
85 Reputation
1 Guide authored
Badges:
4
+1 more badge
Team
UMass Dartmouth, Team S5-G4, Gulbrandsen Fall 2018
Member of UMass Dartmouth, Team S5-G4, Gulbrandsen Fall 2018
UMASSD-GULBRANDSEN-F18S5G4
3 Members
5 Guides authored
Lemmiwinks Rules - Dec 29, 2019
Reply
what size tubing does this require?
S. D. G. - Jan 23, 2021
Reply
Hi Kyle,
Thanks for this. I’m having trouble getting the top to separate. Any suggestions?