Ninja Coffee Bar Cf086 Power Cord Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          1 - 2 hours

Sections

Water Heating Element
12 steps
Power Cord
4 steps

Flags

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Step Trimmer

This guide has unnecessary steps. Trim them to be more concise!

BackNinja Coffee Bar CF086
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Water Heating Element

Make sure the Ninja Coffee Bar is unplugged and that you have a dry, clean workspace for this task.
Remove the carafe and water reservoir and set them aside.

Make sure the Ninja Coffee Bar is unplugged and that you have a dry, clean workspace for this task.

Remove the carafe and water reservoir and set them aside.

1024

Step 2

Unscrew the T-10 screws from the bottom cover of the machine, and remove that bottom cover.

Unscrew the T-10 screws from the bottom cover of the machine, and remove that bottom cover.

Step 3

Unscrew and remove the heating plate layer. This will expose the internal workings of the machine.

Unscrew and remove the heating plate layer. This will expose the internal workings of the machine.

Step 4

Locate the water heating element in the interior of your coffee maker.

Locate the water heating element in the interior of your coffee maker.

Step 5

Unscrew the two indicated J1S1 screws at the base of the water heating element.

Unscrew the two indicated J1S1 screws at the base of the water heating element.

Step 6

Unscrew and remove the remaining J1S1 screws that secure the water heating element to the interior of the device.

Unscrew and remove the remaining J1S1 screws that secure the water heating element to the interior of the device.

Step 7

Grasp and remove the clamp securing the tube that feeds into the base of the water heating element.
Detach the tube from the water heating element.

Grasp and remove the clamp securing the tube that feeds into the base of the water heating element.

Detach the tube from the water heating element.

Step 8

Locate the coated wire that feeds into the side of the water heating element. Remove this wire.

Locate the coated wire that feeds into the side of the water heating element. Remove this wire.

Step 9

Locate the two wires leading out from the water heating element that feed into crimp connectors.
Using side cutters, sever these wires near the crimp connectors.
Use the side cutters to cut the remaining wires that feed into the crimp connectors from the coffee machine.

Locate the two wires leading out from the water heating element that feed into crimp connectors.

Using side cutters, sever these wires near the crimp connectors.

Use the side cutters to cut the remaining wires that feed into the crimp connectors from the coffee machine.

Step 10

Squeeze and remove the clamp that secures the main tube feeding into the water heating element. Remove that tube.
Remove the water heating element.

Squeeze and remove the clamp that secures the main tube feeding into the water heating element. Remove that tube.

Remove the water heating element.

Step 11

Using wire strippers, strip the cut wires from your coffee machine near their cut ends to expose 2 cm of metal conductor from each.
Use a similar procedure to strip the wires from your replacement heating element. Using wire strippers, expose 2 cm of metal conductor from the ends of the wires.

Using wire strippers, strip the cut wires from your coffee machine near their cut ends to expose 2 cm of metal conductor from each.

Use a similar procedure to strip the wires from your replacement heating element. Using wire strippers, expose 2 cm of metal conductor from the ends of the wires.

Step 12

Prepare two crimp connectors by filling them with dielectric grease.
Use a crimp connector to connect a stripped end of the wire leading from the replacement heating element to the stripped end of the corresponding wire from the coffee maker.
Using a second crimp connector, repeat for the remaining pair of stripped wires.
Using the appropriate crimping tool, crimp the connectors.

Prepare two crimp connectors by filling them with dielectric grease.

Use a crimp connector to connect a stripped end of the wire leading from the replacement heating element to the stripped end of the corresponding wire from the coffee maker.

Using a second crimp connector, repeat for the remaining pair of stripped wires.

Using the appropriate crimping tool, crimp the connectors.

Step 13

              Power Cord

The power cord splits into two and feeds into two closed-end crimp connectors. Two wires from your coffee machine also enter these connectors.
Locate the neutral wire that feeds into the crimp connector from the machine. Mark this wire.

The power cord splits into two and feeds into two closed-end crimp connectors. Two wires from your coffee machine also enter these connectors.

Locate the neutral wire that feeds into the crimp connector from the machine. Mark this wire.

Step 14

Using side cutters, cut the wires from your device below the crimp connectors.

Using side cutters, cut the wires from your device below the crimp connectors.

Step 15

Using wire strippers, carefully expose a 2 cm length of the metal wire from each of the cut ends.

Using wire strippers, carefully expose a 2 cm length of the metal wire from each of the cut ends.

Step 16

Apply dielectric grease to the insides of two new crimp connectors.
Insert the stripped ends of the wire into the crimp connectors.
Locate the ends of the replacement power cord. These should be already stripped; if they are not, strip 2 cm from them using wire strippers.
Feed the ends of the replacement power cord into the crimp connectors. Crimp the connectors using the appropriate crimping tool.

Apply dielectric grease to the insides of two new crimp connectors.

Insert the stripped ends of the wire into the crimp connectors.

Locate the ends of the replacement power cord. These should be already stripped; if they are not, strip 2 cm from them using wire strippers.

Feed the ends of the replacement power cord into the crimp connectors. Crimp the connectors using the appropriate crimping tool.

After the wires have been spliced, the new power cord is ready for use with your machine.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors

                    David Ton

Member since: 10/02/2017

552 Reputation

                                      5 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       USF Tampa, Team S1-G5, Thompson Fall 2017                        

                                                  Member of USF Tampa, Team S1-G5, Thompson Fall 2017 



                    USFT-THOMPSON-F17S1G5                     


                                            4 Members                     


                                            5 Guides authored

Needs Better Images#

Step Trimmer#

Introduction#

What you need#

Team#

Needs Better Images

Step Trimmer

Introduction

What you need

Team