Difficulty
Difficult
Steps
8
Time Required
45 minutes
Sections
1
- Film Door
- 8 steps
Flags
Missing Prerequisites
This guide is missing information on how to start the process. Make a prerequisite guide!
BackNikon N80
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Film Door
- Make sure the On/Off switch is in the Off position.
Make sure the On/Off switch is in the Off position.
1024
Step 2
- Remove the four 4.8mm screws on the top section of the camera using a PH00 Phillips screwdriver.
- Two of the screws are located by the viewfinder and and the other two are on each side of the camera.
Remove the four 4.8mm screws on the top section of the camera using a PH00 Phillips screwdriver.
Two of the screws are located by the viewfinder and and the other two are on each side of the camera.
Step 3
- Rotate the camera so the bottom plate is accessible.
- Remove the seven 4.8mm screws on the bottom plate of the camera using a PH00 Phillips screwdriver.
- Remove the two 4.8mm screws on the bottom plate of the camera using a PH00 Phillips screwdriver.
- Remove the bottom plate.
Rotate the camera so the bottom plate is accessible.
Remove the seven 4.8mm screws on the bottom plate of the camera using a PH00 Phillips screwdriver.
Remove the two 4.8mm screws on the bottom plate of the camera using a PH00 Phillips screwdriver.
Remove the bottom plate.
Step 4
- Remove the five silver 4.8mm screws on the lens mount using a PH00 Phillips screwdriver.
- Extract the lens mount.
Remove the five silver 4.8mm screws on the lens mount using a PH00 Phillips screwdriver.
Extract the lens mount.
Step 5
- Remove the seven 4.8mm screws on front camera plate using a PH00 Phillips screwdriver.
- One of the screws is located on the battery chamber side of the camera, two are next to the film door release lever, two are located below the “Nikon” logo, and the last two are located above the “Nikon” logo in the Speedlight compartment.
Remove the seven 4.8mm screws on front camera plate using a PH00 Phillips screwdriver.
One of the screws is located on the battery chamber side of the camera, two are next to the film door release lever, two are located below the “Nikon” logo, and the last two are located above the “Nikon” logo in the Speedlight compartment.
Step 6
- Remove the two 4.8mm screws in the battery compartment of the camera using a PH00 Phillips screwdriver.
- Separate the three front camera plates from the camera.
Remove the two 4.8mm screws in the battery compartment of the camera using a PH00 Phillips screwdriver.
Separate the three front camera plates from the camera.
Step 7
- Gently disconnect the top section of the camera from the body.
- Don’t pull the top section off too hard or the wire and ribbon within the camera may disconnect.
Gently disconnect the top section of the camera from the body.
Don’t pull the top section off too hard or the wire and ribbon within the camera may disconnect.
Step 8
- Turn the camera over to reveal the film door.
- Remove the film door.
Turn the camera over to reveal the film door.
Remove the film door.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 4 other contributors
Maegan Viloria
Member since: 09/14/2015
696 Reputation
5 Guides authored
Badges:
8
+5 more badges
Team
CSU Fullerton, Team 1-7, Bruce Fall 2015
Member of CSU Fullerton, Team 1-7, Bruce Fall 2015
CSUF-BRUCE-F15S1G7
3 Members
6 Guides authored
tadeuszse - Apr 19, 2019
Reply
To replace the camera door, simply unscrew one screw under the door and three screws in the door to disconnect the cable that connects the camera to the door.
jenrossiter - Nov 27, 2019
Reply
Hi where can buy a replacement door please?
D S - Sep 7, 2020
Uscamera.com carries them.
Bruce H McIntosh - Sep 17, 2022
Reply
It’s unnecessary to disassemble the camera to this extent. You just need to disconnect the ribbon cable (which involves removing the spring loaded guide next to the door hinge and unlatch the connector underneath) and unscrew the door pivot screw on the underside of the camera. This document lays it out quite nicely:https://www.jeremymuddphoto.com/blog/202…
gabrielpurziani - Sep 18, 2022
Reply
Thank you all for the information.