Difficulty

Moderate

Steps

10

Time Required

Suggest a time??

Sections

1

  • GPS PCB
  • 10 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackNikon D90

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Replacement of the electronic card including the GPS connector, DC IN, and AV out.

What you need

Step 1

              Remove the bottom cover
  • Remove the three screw in red
  • Remove the three long screw in orange
  • Remove the screw in yellow
  • Use a little of WD40 if the screw is blocked

Remove the three screw in red

Remove the three long screw in orange

Remove the screw in yellow

Use a little of WD40 if the screw is blocked

1024

Step 2

              Remove the back cover
  • Remove the 4 screw in green
  • Remove the 2 screw in yellow

Remove the 4 screw in green

Remove the 2 screw in yellow

Step 3

  • Slacken the grip side of the cover first
  • Remove the cover wholly.
  • Be carefull with the two flex cables

Slacken the grip side of the cover first

Remove the cover wholly.

Be carefull with the two flex cables

Step 4

  • Disconnect the FPC of the back cover
  • Toggle up the black plate to free the flex cable
  • Remove the grip cover by rotating

Disconnect the FPC of the back cover

Toggle up the black plate to free the flex cable

Remove the grip cover by rotating

Step 5

              Disconnect all the cables - part 1/3
  • Toggle up the black plate and disconnect the flex cable
  • Toggle up the white plate and disconnect the flex cable
  • Push up the right slide of the connector to free it

Toggle up the black plate and disconnect the flex cable

Toggle up the white plate and disconnect the flex cable

Push up the right slide of the connector to free it

Step 6

              Disconnect all the cables - part 2/3
  • Push up the bottom of the connector to free it

Push up the bottom of the connector to free it

Step 7

              Detach the protection plate
  • Remove the six screws to free the protection plate
  • Disconnect the white cables
  • Disconnect the microphone Cable

Remove the six screws to free the protection plate

Disconnect the white cables

Disconnect the microphone Cable

Step 8

              Disconnect all cables - Part 3/3
  • Disconnect the speaker cable
  • Remove the two screws to free the PCB
  • Toggle th PCB from Left to Right

Disconnect the speaker cable

Remove the two screws to free the PCB

Toggle th PCB from Left to Right

Step 9

              Disconnect the cable on the bottom of the PCB
  • Disconnect the black cables

Disconnect the black cables

Step 10

              Free the IF/SB PCB
  • Remove the two screws
  • Push the IF/SB PCB
  • Unsolder the 3 Wires ( Red, Black, Orange )

Remove the two screws

Push the IF/SB PCB

Unsolder the 3 Wires ( Red, Black, Orange )

To reassemble your device, follow the instructions in reverse order.

Cancel: I did not complete this guide.

        These translators are helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

JOLY

irlanda

Author

                                      with 1 other contributor 


                    JOLY

Member since: 03/06/2016

182 Reputation

                                      1 Guide authored                  



                       Badges:
                       1

Team

                       Nexurium - Bastien JOLY                        

                                                  Member of Nexurium - Bastien JOLY 



                    Business                     


                                            1 Member                     


                                            2 Guides authored