Difficulty

Moderate

Steps

18

Time Required

Suggest a time??

Sections

3

  • Rear Case
  • 10 steps
  • LCD
  • 6 steps
  • Rear LCD Glass
  • 2 steps

Flags

0

  • BackNikon D90

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Rear Case
  • Slide the eyepiece up and off the viewfinder.

Slide the eyepiece up and off the viewfinder.

1024

Step 2

  • Using a PH000 screwdriver, remove the two 4.8mm Phillips screws from the back of the viewfinder.
  • Some screws may be JIS. Be wary of this if your PH000 does not feel like it is properly gripping the screws.

Using a PH000 screwdriver, remove the two 4.8mm Phillips screws from the back of the viewfinder.

Some screws may be JIS. Be wary of this if your PH000 does not feel like it is properly gripping the screws.

Step 3

  • Remove the two 6.4mm Phillips screws on the right side of the camera, near the SD card slot.

Remove the two 6.4mm Phillips screws on the right side of the camera, near the SD card slot.

Step 4

  • Remove the two 6.4mm Phillips screws on the left side of the camera, near the I/O ports.

Remove the two 6.4mm Phillips screws on the left side of the camera, near the I/O ports.

Step 5

  • On the bottom of the camera,
  • remove the two 5.3mm Phillips screws
  • and the other two 6.3mm Phillips screws.

On the bottom of the camera,

remove the two 5.3mm Phillips screws

and the other two 6.3mm Phillips screws.

Step 6

  • Using a spudger, separate the bottom panel from the rear case just enough to clear the two clips on the rear casing in the next step.

Using a spudger, separate the bottom panel from the rear case just enough to clear the two clips on the rear casing in the next step.

Step 7

  • Lift the rear case off of the back of the camera.
  • Don’t pull the casing completely off yet, as the ribbon cables are still connected.
  • Be mindful of the two clips, making sure to keep the bottom panel far enough away to clear them.

Lift the rear case off of the back of the camera.

Don’t pull the casing completely off yet, as the ribbon cables are still connected.

Be mindful of the two clips, making sure to keep the bottom panel far enough away to clear them.

Step 8

  • Set the rear casing off to the side so you can access the ZIF connectors.
  • The orientation shown in the picture seems to be the best position for the casing to sit comfortably without stressing the ribbon cable connections.

Set the rear casing off to the side so you can access the ZIF connectors.

The orientation shown in the picture seems to be the best position for the casing to sit comfortably without stressing the ribbon cable connections.

Step 9

  • Use a spudger to lift the black tab on the ZIF connector.
  • Disconnect the ribbon cables from their respective ZIF connectors on the logic board.

Use a spudger to lift the black tab on the ZIF connector.

Disconnect the ribbon cables from their respective ZIF connectors on the logic board.

Step 10

  • Separate the rear casing from the camera.

Separate the rear casing from the camera.

Step 11

              LCD
  • Peel back the yellow tape covering the cable connector on the back of the casing you removed.

Peel back the yellow tape covering the cable connector on the back of the casing you removed.

Step 12

  • Using the spudger, rock the connector back and forth to disconnect the cable.

Using the spudger, rock the connector back and forth to disconnect the cable.

Step 13

  • Remove the eight Phillips screws securing the brackets to the rear casing.
  • Four 4.2mm screws securing the large metal bracket.
  • Four 3.4mm screws securing the bracket that covers the ribbon cable.

Remove the eight Phillips screws securing the brackets to the rear casing.

Four 4.2mm screws securing the large metal bracket.

Four 3.4mm screws securing the bracket that covers the ribbon cable.

Step 14

  • Remove the silver metal plate.

Remove the silver metal plate.

Step 15

  • Fold the ribbon cables up and out of the way.
  • Remove the metal shield covering the LCD.

Fold the ribbon cables up and out of the way.

Remove the metal shield covering the LCD.

Step 16

  • Lift and remove the LCD from the rear case.

Lift and remove the LCD from the rear case.

Step 17

              Rear LCD Glass
  • Using either the iOpener or a heat gun, heat the rear LCD glass enough to melt the adhesive holding it on.
  • The glass will be hot! Let cool before handling.

Using either the iOpener or a heat gun, heat the rear LCD glass enough to melt the adhesive holding it on.

The glass will be hot! Let cool before handling.

Step 18

  • Push the glass out from the back side.

Push the glass out from the back side.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      9 other people completed this guide.

Author

                                      with 1 other contributor 


                    Ryan Lutz

Member since: 09/27/2011

2,981 Reputation

                                      3 Guides authored                  



                       Badges:
                       32







                                                        +29 more badges