Difficulty
Easy
Steps
8
Time Required
5 - 15 minutes
Sections
2
- Battery
- 4 steps
- Back Panel
- 4 steps
Flags
0
BackNikon CoolPix S9700
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Press the ON/OFF button to power off the S9700.
- Not doing so can damage the S9700 or cause electric shock.
Press the ON/OFF button to power off the S9700.
Not doing so can damage the S9700 or cause electric shock.
1024
Step 2
- Place the S9700 upside down
- Place your finger on the battery compartment cover and gently push toward the front of the S9700.
- The cover will open up by itself.
Place the S9700 upside down
Place your finger on the battery compartment cover and gently push toward the front of the S9700.
The cover will open up by itself.
Step 3
- Push the yellow tab inside the battery compartment in the direction of the arrow. This will allow the battery to spring up.
Push the yellow tab inside the battery compartment in the direction of the arrow. This will allow the battery to spring up.
Step 4
- Grab the battery and pull out.
Grab the battery and pull out.
Step 5
Back Panel
- Remove the two 4-mm and three 3-mm J000 screws from the bottom of the S9700.
- Three 3-mm screws are on the side opposite the battery compartment.
- Two 4-mm screws are on the side with the battery compartment. One of these screws is in the battery compartment. Open it up for access.
Remove the two 4-mm and three 3-mm J000 screws from the bottom of the S9700.
Three 3-mm screws are on the side opposite the battery compartment.
Two 4-mm screws are on the side with the battery compartment. One of these screws is in the battery compartment. Open it up for access.
Step 6
- Remove the one 3-mm J000 screw on the left side of the S9700 (side with no ports).
- Remove the two 3-mm J000 screws on the right side (side with HDMI and charging ports).
- One of these screws is underneath the HDMI port cover. Lift the port cover up to access.
Remove the one 3-mm J000 screw on the left side of the S9700 (side with no ports).
Remove the two 3-mm J000 screws on the right side (side with HDMI and charging ports).
One of these screws is underneath the HDMI port cover. Lift the port cover up to access.
Step 7
- Insert the plastic opening tool on the bottom of the S9700 between the front panel and the back panel.
- Twist the plastic opening tool so that both halves separate.
- When both halves are separated, the HDMI cover, charging cover, and the ON/OFF switch will fall out.
- There is a flex ribbon attached to the back panel. Forcing the back panel off may rip it.
Insert the plastic opening tool on the bottom of the S9700 between the front panel and the back panel.
Twist the plastic opening tool so that both halves separate.
When both halves are separated, the HDMI cover, charging cover, and the ON/OFF switch will fall out.
There is a flex ribbon attached to the back panel. Forcing the back panel off may rip it.
Step 8
- Remove the three silver 3-mm J000 screws on the back panel holding the silver button / dial component to the panel and ribbon.
- Gently remove the back panel.
Remove the three silver 3-mm J000 screws on the back panel holding the silver button / dial component to the panel and ribbon.
Gently remove the back panel.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Matt Staubus
Member since: 10/05/2016
801 Reputation
5 Guides authored
Badges:
14
+11 more badges
Team
USF Tampa, Team 9-5, Lacy Fall 2016
Member of USF Tampa, Team 9-5, Lacy Fall 2016
USFT-LACY-F16S9G5
4 Members
10 Guides authored
