Difficulty

Moderate

Steps

12

Time Required

                          35 minutes

Sections

4

  • Battery
  • 2 steps
  • Buttons
  • 5 steps
  • Display
  • 1 step
  • Polarizing Lens
  • 4 steps

Flags

Bullets!

Better coordination with markups and the color/type of bullets will help make this guide more clear!

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Missed a Step

Oops! This guide is currently missing some important steps.

  • BackNikon Coolpix S6300

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Place the camera facing upwards.
  • Press down on the battery cover and slide towards the front face of the camera.

Place the camera facing upwards.

Press down on the battery cover and slide towards the front face of the camera.

1024

Step 2

  • Rotate the orange battery clip in the camera to release the battery.

Rotate the orange battery clip in the camera to release the battery.

Step 3

              Buttons
  • Locate the eight outer PH 2mm screws on the device.
  • Using the PH00 screwdriver remove all of the screws from the camera.

Locate the eight outer PH 2mm screws on the device.

Using the PH00 screwdriver remove all of the screws from the camera.

Step 4

  • Using a plastic opening tool, gently pry off the front and rear plates.
  • Be patient with this step, do not force the clips holding the plates together.

Using a plastic opening tool, gently pry off the front and rear plates.

Be patient with this step, do not force the clips holding the plates together.

Step 5

  • Using a Phillips #00 screwdriver, remove the PH 2mm screw located to the right of the screen, above the OK dial.

Using a Phillips #00 screwdriver, remove the PH 2mm screw located to the right of the screen, above the OK dial.

Step 6

  • Remove the two clasp using a plastic spudger
  • Be careful when removing the clasp to prevent ripping of the clasp

Remove the two clasp using a plastic spudger

Be careful when removing the clasp to prevent ripping of the clasp

Step 7

  • You may now remove the internal panel of the buttons

You may now remove the internal panel of the buttons

Step 8

              Display
  • Remove the clasp from the ribbon cable using the plastic spudger.
  • Make sure to be gentle when removing the clasp to prevent it from ripping.
  • You may now remove the display.

Remove the clasp from the ribbon cable using the plastic spudger.

Make sure to be gentle when removing the clasp to prevent it from ripping.

You may now remove the display.

Step 9

              Polarizing Lens
  • Remove the four PH00 2.5 mm screws around the edges of the display plate.
  • Remove the three PH00 2 mm screws from the sides of the buttons plate and the 2.5 mm screw from the center of the buttons plate.
  • Lift the buttons plate out of the camera with the plastic tool.
  • Lift the display plate out of the camera with the plastic tool.

Remove the four PH00 2.5 mm screws around the edges of the display plate.

Remove the three PH00 2 mm screws from the sides of the buttons plate and the 2.5 mm screw from the center of the buttons plate.

Lift the buttons plate out of the camera with the plastic tool.

Lift the display plate out of the camera with the plastic tool.

Step 10

  • Use the plastic opening tool to gently flip the white folders at the end of the ribbon cables.
  • Use this tweezers to gently pull the cables out of the holders.
  • Lift the lens apparatus out of the rest of the camera by pushing the front of lens up from the bottom.

Use the plastic opening tool to gently flip the white folders at the end of the ribbon cables.

Use this tweezers to gently pull the cables out of the holders.

Lift the lens apparatus out of the rest of the camera by pushing the front of lens up from the bottom.

Step 11

  • Use the plastic opening tool to flip the two white clips holding the ribbon cables.
  • Use tweezers to pull the cables from clamps.
  • Use the PH00 screwdriver to remove the three 2 mm screws around the first lens area.

Use the plastic opening tool to flip the two white clips holding the ribbon cables.

Use tweezers to pull the cables from clamps.

Use the PH00 screwdriver to remove the three 2 mm screws around the first lens area.

Step 12

  • Lift the first lens from the rest of the lens apparatus.
  • Use thin tweezers to left and remove the polarizing lens from the apparatus.

Lift the first lens from the rest of the lens apparatus.

Use thin tweezers to left and remove the polarizing lens from the apparatus.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 2 other contributors 


                    Michael Lynch

Member since: 08/31/2015

396 Reputation

                                      3 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       USF Tampa, Team 1-2, Remmell Fall 2015                        

                                                  Member of USF Tampa, Team 1-2, Remmell Fall 2015 



                    USFT-REMMELL-F15S1G2                     


                                            5 Members                     


                                            10 Guides authored