Difficulty
Difficult
Steps
17
Time Required
30 minutes
Sections
3
- Front and Rear Casing
- 10 steps
- Lens Assembly
- 6 steps
- Motherboard Assembly
- 1 step
Flags
Needs Better Images
Better photos will improve this guide. Help out by taking, editing, or uploading new ones!
Missed a Step
Oops! This guide is currently missing some important steps.
Better Introduction
Improve this guide by completing or revising its introduction.
BackNikon CoolPix S600
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Front and Rear Casing
- With the lens facing forward, remove the one 4.2 mm screw on the bottom right hand corner of the camera.
With the lens facing forward, remove the one 4.2 mm screw on the bottom right hand corner of the camera.
1024
Step 2
- Remove the chrome side cover from the body of the camera.
Remove the chrome side cover from the body of the camera.
Step 3
- Remove the four 3.2 mm screws on the bottom of the camera.
Remove the four 3.2 mm screws on the bottom of the camera.
Step 4
- Remove the two 3.2 mm screws from the right side of the camera (with lens is facing forward)
- Remove the one 3.2 mm screw from the left side of the camera (with lens facing foward)
Remove the two 3.2 mm screws from the right side of the camera (with lens is facing forward)
Remove the one 3.2 mm screw from the left side of the camera (with lens facing foward)
Step 5
- Gently separate the back cover from the body of the camera.
- The back casing will still be connected to the circuit board by a ribbon
Gently separate the back cover from the body of the camera.
The back casing will still be connected to the circuit board by a ribbon
Step 6
- Use the tweezers to disconnect the ribbon from the circuit board.
Use the tweezers to disconnect the ribbon from the circuit board.
Step 7
- Remove the one 2.6 mm screw from the left side of the camera (with the lens facing forward)
Remove the one 2.6 mm screw from the left side of the camera (with the lens facing forward)
Step 8
- Gently separate the front cover from the body of the camera.
- The front casing will still be connected to the circuit board by a few wires
Gently separate the front cover from the body of the camera.
The front casing will still be connected to the circuit board by a few wires
Step 9
- Remove the two 3.2 mm screws that hold the flash to the front cover.
Remove the two 3.2 mm screws that hold the flash to the front cover.
Step 10
- Use the Spudger to remove the copper colored light bulb clip.
- Remove the front cover entierly from the camera body.
Use the Spudger to remove the copper colored light bulb clip.
Remove the front cover entierly from the camera body.
Step 11
Lens Assembly
- From the top view of the camera, remove the one 5.8 mm screw.
- From the top view of the camera, remove the one 2.8 mm screw
From the top view of the camera, remove the one 5.8 mm screw.
From the top view of the camera, remove the one 2.8 mm screw
Step 12
- Remove the three 3.4 mm screws from the back side of the camera.
Remove the three 3.4 mm screws from the back side of the camera.
Step 13
- Remove the two 3.4 mm screws from the side of the camera.
Remove the two 3.4 mm screws from the side of the camera.
Step 14
- Separate the two metal body pieces from the rest of the camera.
Separate the two metal body pieces from the rest of the camera.
Step 15
- Gently remove the two ribbons connecting the lens to the mother board.
Gently remove the two ribbons connecting the lens to the mother board.
Step 16
- Gently separate the camera lens from the mother board.
Gently separate the camera lens from the mother board.
Step 17
Motherboard Assembly
- The mother board is permanently fixed to the battery housing.
- Mother board cannot be taken a part any further.
The mother board is permanently fixed to the battery housing.
Mother board cannot be taken a part any further.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 5 other contributors
andreas anggasastra
Member since: 09/14/2011
116 Reputation
5 Guides authored
Badges:
5
+2 more badges
Team
Cuesta, Team 1-6, Zipperian Fall 2011
Member of Cuesta, Team 1-6, Zipperian Fall 2011
CUESTA-ZIPPERIAN-F11S1G6
2 Members
6 Guides authored
