Difficulty

Difficult

Steps

16

Time Required

                          30 minutes

Sections

2

  • Front and Rear Casing
  • 10 steps
  • Lens Assembly
  • 6 steps

Flags

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackNikon CoolPix S600

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Front and Rear Casing
  • With the lens facing forward, remove the one 4.2 mm screw on the bottom right hand corner of the camera.

With the lens facing forward, remove the one 4.2 mm screw on the bottom right hand corner of the camera.

1024

Step 2

  • Remove the chrome side cover from the body of the camera.

Remove the chrome side cover from the body of the camera.

Step 3

  • Remove the four 3.2 mm screws on the bottom of the camera.

Remove the four 3.2 mm screws on the bottom of the camera.

Step 4

  • Remove the two 3.2 mm screws from the right side of the camera (with lens is facing forward)
  • Remove the one 3.2 mm screw from the left side of the camera (with lens facing foward)

Remove the two 3.2 mm screws from the right side of the camera (with lens is facing forward)

Remove the one 3.2 mm screw from the left side of the camera (with lens facing foward)

Step 5

  • Gently separate the back cover from the body of the camera.
  • The back casing will still be connected to the circuit board by a ribbon

Gently separate the back cover from the body of the camera.

The back casing will still be connected to the circuit board by a ribbon

Step 6

  • Use the tweezers to disconnect the ribbon from the circuit board.

Use the tweezers to disconnect the ribbon from the circuit board.

Step 7

  • Remove the one 2.6 mm screw from the left side of the camera (with the lens facing forward)

Remove the one 2.6 mm screw from the left side of the camera (with the lens facing forward)

Step 8

  • Gently separate the front cover from the body of the camera.
  • The front casing will still be connected to the circuit board by a few wires

Gently separate the front cover from the body of the camera.

The front casing will still be connected to the circuit board by a few wires

Step 9

  • Remove the two 3.2 mm screws that hold the flash to the front cover.

Remove the two 3.2 mm screws that hold the flash to the front cover.

Step 10

  • Use the Spudger to remove the copper colored light bulb clip.
  • Remove the front cover entierly from the camera body.

Use the Spudger to remove the copper colored light bulb clip.

Remove the front cover entierly from the camera body.

Step 11

              Lens Assembly
  • From the top view of the camera, remove the one 5.8 mm screw.
  • From the top view of the camera, remove the one 2.8 mm screw

From the top view of the camera, remove the one 5.8 mm screw.

From the top view of the camera, remove the one 2.8 mm screw

Step 12

  • Remove the three 3.4 mm screws from the back side of the camera.

Remove the three 3.4 mm screws from the back side of the camera.

Step 13

  • Remove the two 3.4 mm screws from the side of the camera.

Remove the two 3.4 mm screws from the side of the camera.

Step 14

  • Separate the two metal body pieces from the rest of the camera.

Separate the two metal body pieces from the rest of the camera.

Step 15

  • Gently remove the two ribbons connecting the lens to the mother board.

Gently remove the two ribbons connecting the lens to the mother board.

Step 16

  • Gently separate the camera lens from the mother board.

Gently separate the camera lens from the mother board.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 5 other contributors 


                    andreas anggasastra

Member since: 09/14/2011

116 Reputation

                                      5 Guides authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       Cuesta, Team 1-6, Zipperian Fall 2011                        

                                                  Member of Cuesta, Team 1-6, Zipperian Fall 2011 



                    CUESTA-ZIPPERIAN-F11S1G6                     


                                            2 Members                     


                                            6 Guides authored

thesilver - Apr 13, 2014

Reply

Any place where I could buy a new lens for the camera nowadays?