Nikon Coolpix S5300 Lcd Display Screen Replacement Repair Guide

Difficulty

Moderate

Steps

12

Time Required

                          20 minutes            

Sections

4

• Battery
• 2 steps
• Outer Casing
• 5 steps
• Button Panel
• 2 steps
• LCD Display Screen
• 3 steps

Flags

0

• BackNikon Coolpix S5300

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

• Disassemble the camera.Replace the screen.Properly reassemble the components involved.

What you need

Step 1

              Battery               

• Turn the camera upside down and locate the battery compartment.
• Slide the compartment open following the direction of the arrow.

Turn the camera upside down and locate the battery compartment.

Slide the compartment open following the direction of the arrow.

1024

Step 2

• Press the orange release button to release and remove the battery.
• Replace or insert battery in it’s respective terminals

Press the orange release button to release and remove the battery.

Replace or insert battery in it’s respective terminals

Step 3

              Outer Casing               

• Remove the four 0.1mm screws from the bottom of the camera using the phillips head screwdriver
• Using the same screwdriver, remove the 2 screws on the side of the camera.
• Remove the 2 screws from the other side of the camera.
• One of the screws is under the I/O port cover.

Remove the four 0.1mm screws from the bottom of the camera using the phillips head screwdriver

Using the same screwdriver, remove the 2 screws on the side of the camera.

Remove the 2 screws from the other side of the camera.

One of the screws is under the I/O port cover.

Step 4

• Use the plastic opening tool to carefully separate the cover from the camera.
• Work the plastic opening tool around all the edges of the front plate.
• Pull the purple plastic cover off gently from the screen.

Use the plastic opening tool to carefully separate the cover from the camera.

Work the plastic opening tool around all the edges of the front plate.

Pull the purple plastic cover off gently from the screen.

Step 5

• Turn the camera over so the LCD screen is facing you.
• Carefully remove the front shell by gently prying around the corners with the plastic opening tool until it releases.

Turn the camera over so the LCD screen is facing you.

Carefully remove the front shell by gently prying around the corners with the plastic opening tool until it releases.

Step 6

• Be careful to keep track of little pieces of the outside casing.

Be careful to keep track of little pieces of the outside casing.

Step 7

• Carefully remove the top button casing by pulling it away from main camera.

Carefully remove the top button casing by pulling it away from main camera.

Step 8

              Button Panel               

• Remove the 2 screws on the silver plate
• Gently lift the screen and silver plate away from the internal components.
• Do not separate the plate and screen from the camera

Remove the 2 screws on the silver plate

Gently lift the screen and silver plate away from the internal components.

Do not separate the plate and screen from the camera

Step 9

• Carefully move the button panel away from the silver plate.
• To disconnect the ribbon cable, use the tip of a plastic opening tool or your fingernail to flip up the small retaining flap.
• Safely pull the ribbon cable out and then remove the button panel.
• Be sure you are prying up on the hinged retaining flap, not the connector itself.

Carefully move the button panel away from the silver plate.

To disconnect the ribbon cable, use the tip of a plastic opening tool or your fingernail to flip up the small retaining flap.

Safely pull the ribbon cable out and then remove the button panel.

Be sure you are prying up on the hinged retaining flap, not the connector itself.

Step 10

              LCD Display Screen               

• Carefully remove the screen away from the silver plate.
• Carefully fold the screen over exposing the latch for the ribbon cable.

Carefully remove the screen away from the silver plate.

Carefully fold the screen over exposing the latch for the ribbon cable.

Step 11

• To disconnect the ribbon cable, use the tip of a plastic opening tool or your fingernail to flip up the small retaining flap. Then, you can safely pull the ribbon cable out.
• Be sure you are prying up on the hinged retaining flap, not the connector itself.

To disconnect the ribbon cable, use the tip of a plastic opening tool or your fingernail to flip up the small retaining flap. Then, you can safely pull the ribbon cable out.

Step 12

• Once the ribbon cable is disconnected, remove the LCD screen.

Once the ribbon cable is disconnected, remove the LCD screen.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 

                    Waleed Chakir                     

Member since: 03/04/2016

301 Reputation

                                      3 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges                           

Team

                       UMass Dartmouth, Team 6-1, Bhusal Spring 2016                        

                                                  Member of UMass Dartmouth, Team 6-1, Bhusal Spring 2016 



                    UMASSD-BHUSAL-S16S6G1                     


                                            3 Members                     


                                            12 Guides authored