Difficulty
Moderate
Steps
9
Time Required
15 minutes
Sections
3
- Battery
- 2 steps
- Outer Casing
- 5 steps
- Button Panel
- 2 steps
Flags
0
BackNikon Coolpix S5300
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
- Make sure to be gentle when removing ribbon cables. Be sure to keep track of all your screws.
What you need
Step 1
Battery
- Turn the camera upside down and locate the battery compartment.
- Slide the compartment open following the direction of the arrow.
Turn the camera upside down and locate the battery compartment.
Slide the compartment open following the direction of the arrow.
1024
Step 2
- Press the orange release button to release and remove the battery.
- Replace or insert battery in it’s respective terminals
Press the orange release button to release and remove the battery.
Replace or insert battery in it’s respective terminals
Step 3
Outer Casing
- Remove the four 0.1mm screws from the bottom of the camera using the phillips head screwdriver
- Using the same screwdriver, remove the 2 screws on the side of the camera.
- Remove the 2 screws from the other side of the camera.
- One of the screws is under the I/O port cover.
Remove the four 0.1mm screws from the bottom of the camera using the phillips head screwdriver
Using the same screwdriver, remove the 2 screws on the side of the camera.
Remove the 2 screws from the other side of the camera.
One of the screws is under the I/O port cover.
Step 4
- Use the plastic opening tool to carefully separate the cover from the camera.
- Work the plastic opening tool around all the edges of the front plate.
- Pull the purple plastic cover off gently from the screen.
Use the plastic opening tool to carefully separate the cover from the camera.
Work the plastic opening tool around all the edges of the front plate.
Pull the purple plastic cover off gently from the screen.
Step 5
- Turn the camera over so the LCD screen is facing you.
- Carefully remove the front shell by gently prying around the corners with the plastic opening tool until it releases.
Turn the camera over so the LCD screen is facing you.
Carefully remove the front shell by gently prying around the corners with the plastic opening tool until it releases.
Step 6
- Be careful to keep track of little pieces of the outside casing.
Be careful to keep track of little pieces of the outside casing.
Step 7
- Carefully remove the top button casing by pulling it away from main camera.
Carefully remove the top button casing by pulling it away from main camera.
Step 8
Button Panel
- Remove the 2 screws on the silver plate
- Gently lift the screen and silver plate away from the internal components.
- Do not separate the plate and screen from the camera
Remove the 2 screws on the silver plate
Gently lift the screen and silver plate away from the internal components.
Do not separate the plate and screen from the camera
Step 9
- Carefully move the button panel away from the silver plate.
- To disconnect the ribbon cable, use the tip of a plastic opening tool or your fingernail to flip up the small retaining flap.
- Safely pull the ribbon cable out and then remove the button panel.
- Be sure you are prying up on the hinged retaining flap, not the connector itself.
Carefully move the button panel away from the silver plate.
To disconnect the ribbon cable, use the tip of a plastic opening tool or your fingernail to flip up the small retaining flap.
Safely pull the ribbon cable out and then remove the button panel.
Be sure you are prying up on the hinged retaining flap, not the connector itself.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Waleed Chakir
Member since: 03/04/2016
301 Reputation
3 Guides authored
Badges:
6
+3 more badges
Team
UMass Dartmouth, Team 6-1, Bhusal Spring 2016
Member of UMass Dartmouth, Team 6-1, Bhusal Spring 2016
UMASSD-BHUSAL-S16S6G1
3 Members
12 Guides authored
