Nikon Coolpix S4100 Lcd Screen Replacement Repair Guide

Difficulty

Moderate

Steps

17

Time Required

                          15 minutes            

Sections

3

• External Casing
• 11 steps
• Functional Button Plate
• 3 steps
• LCD Screen
• 3 steps

Flags

2

Markup Mishap

This guide needs better markups. Help out by correcting or making some markup annotations.

Needs More Images

A few more images would make this guide’s procedures crystal clear.

• BackNikon Coolpix S4100

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              External Casing               

• Using a Philips #000 head screwdriver, remove the 8 screws (3.30 mm) visible on the external part of the camera.
• There are 2 on each side, and 4 on the bottom.

Using a Philips #000 head screwdriver, remove the 8 screws (3.30 mm) visible on the external part of the camera.

There are 2 on each side, and 4 on the bottom.

1024

Step 2

• Remove the black casing on the back of the camera that runs around the LCD screen.

Remove the black casing on the back of the camera that runs around the LCD screen.

Step 3

• Using the Philips #000 head screwdriver, remove the 1.90 mm internal screw located just above the lanyard mount.

Using the Philips #000 head screwdriver, remove the 1.90 mm internal screw located just above the lanyard mount.

Step 4

• Pry off the front shell casing.
• If you find this difficult, use a prying tool to help gently remove the casing.

Pry off the front shell casing.

If you find this difficult, use a prying tool to help gently remove the casing.

Step 5

• Using the Philips #000 head screwdriver, remove the 3.30 mm screw located on the side of the camera near the lanyard mount.

Using the Philips #000 head screwdriver, remove the 3.30 mm screw located on the side of the camera near the lanyard mount.

Step 6

• Using the Philips #000 head screwdriver, remove 2 additional 3.30 mm screws holding the lanyard mount in place.

Using the Philips #000 head screwdriver, remove 2 additional 3.30 mm screws holding the lanyard mount in place.

Step 7

• Remove the lanyard mount and accompanying side shell casing off of the camera.

Remove the lanyard mount and accompanying side shell casing off of the camera.

Step 8

• Using the Philips #000 head screwdriver, remove the 3.30 mm screw securing the top shell casing.

Using the Philips #000 head screwdriver, remove the 3.30 mm screw securing the top shell casing.

Step 9

• Using the Philips #000 head screwdriver, remove the 3.40 mm screw located on the front of the camera in the upper corner by the LED light.

Using the Philips #000 head screwdriver, remove the 3.40 mm screw located on the front of the camera in the upper corner by the LED light.

Step 10

• Remove the remaining side shell casing.

Remove the remaining side shell casing.

Step 11

• Remove the top shell casing.

Remove the top shell casing.

Step 12

              Functional Button Plate               

• Using the Philips #000 head screwdriver, remove the 3.40 mm screw located near the functional buttons.

Using the Philips #000 head screwdriver, remove the 3.40 mm screw located near the functional buttons.

Step 13

• Using precision tweezers, remove the ribbon cable that runs from the functional buttons plate to the under side of the motherboard.

Using precision tweezers, remove the ribbon cable that runs from the functional buttons plate to the under side of the motherboard.

Step 14

• Using precision tweezers, lift up the bottom of the functional buttons plate and remove the metal plate.

Using precision tweezers, lift up the bottom of the functional buttons plate and remove the metal plate.

Step 15

              LCD Screen               

• Using precision tweezers, gently remove the ribbon cable running from LCD to the bottom side of the motherboard.

Using precision tweezers, gently remove the ribbon cable running from LCD to the bottom side of the motherboard.

Step 16

• Using precision tweezers, gently lift up on the black strip of the ZIF Connector securing the cable from the LCD to the motherboard.
• Then, gently remove the wire by pulling the base of the ribbon cable towards the LCD screen.
• Do not poke or destroy the cable itself. Be careful to only grab the black fold in the tweezers.
• The black strip will fold back to reveal the cable, but remain attached to the motherboard.

Using precision tweezers, gently lift up on the black strip of the ZIF Connector securing the cable from the LCD to the motherboard.

Then, gently remove the wire by pulling the base of the ribbon cable towards the LCD screen.

Do not poke or destroy the cable itself. Be careful to only grab the black fold in the tweezers.

The black strip will fold back to reveal the cable, but remain attached to the motherboard.

Step 17

• Remove the LCD screen from the metal mount.

Remove the LCD screen from the metal mount.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors 

                    Matthew Willis                     

Member since: 09/22/2015

574 Reputation

                                      4 Guides authored                  



                       Badges:
                       12







                                                        +9 more badges                           

Team

                       Baylor, Team 4-2, Williams Fall 2015                        

                                                  Member of Baylor, Team 4-2, Williams Fall 2015 



                    BU-WILLIAMS-F15S4G2                     


                                            4 Members                     


                                            8 Guides authored