Difficulty

Easy

Steps

10

Time Required

                          3 minutes

Sections

4

  • Battery
  • 2 steps
  • Casing
  • 3 steps
  • Lens Casing
  • 2 steps
  • Screen
  • 3 steps

Flags

0

  • BackNikon Coolpix S4000

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Slide the battery door open with a finger or thumb and release it so the door opens.

Slide the battery door open with a finger or thumb and release it so the door opens.

1024

Step 2

  • Push the orange tab back and the battery will pop out.

Push the orange tab back and the battery will pop out.

Step 3

              Casing
  • Remove four 2mm Phillips #000 screws.
  • Remove two black 3mm Phillips #000 screws.
  • Remove one 4mm Phillips #000 screws.
  • Remove two silver 3mm Phillips #000 screws.

Remove four 2mm Phillips #000 screws.

Remove two black 3mm Phillips #000 screws.

Remove one 4mm Phillips #000 screws.

Remove two silver 3mm Phillips #000 screws.

Step 4

  • Use your fingers, or a spudger, to lift up one end of the casing and then pry the two pieces apart.

Use your fingers, or a spudger, to lift up one end of the casing and then pry the two pieces apart.

Step 5

  • Turn the camera over.
  • Use your fingers, or spudger, to lift one end of the back casing and pry it apart from back of the camera.

Turn the camera over.

Use your fingers, or spudger, to lift one end of the back casing and pry it apart from back of the camera.

Step 6

              Lens Casing
  • Remove the single 3mm Phillips #000 screw from the back of the camera.

Remove the single 3mm Phillips #000 screw from the back of the camera.

Step 7

  • Turn the camera over and pry the lens casing off by slipping your fingers, or spudger, under the lip of the casing.
  • Desolder the two wires connecting the casing to the motherboard.
  • Work carefully so that you do not break the soldered wires.

Turn the camera over and pry the lens casing off by slipping your fingers, or spudger, under the lip of the casing.

Desolder the two wires connecting the casing to the motherboard.

Work carefully so that you do not break the soldered wires.

Step 8

              Screen
  • Remove the single 2mm Phillips #000 screw.

Remove the single 2mm Phillips #000 screw.

Step 9

  • Use the flat end of a spudger to lift up the black tabs on the ZIF connectors.
  • Pull the ribbon cables out of the ZIF connectors.

Use the flat end of a spudger to lift up the black tabs on the ZIF connectors.

Pull the ribbon cables out of the ZIF connectors.

Step 10

  • Grabbing the top left corner of the screen, pull it up until the screen comes completely off.

Grabbing the top left corner of the screen, pull it up until the screen comes completely off.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Matina Newsom

Member since: 02/21/2018

755 Reputation

                                      8 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       University of North Texas, Team S4-G1, Thompson Spring 2018                        

                                                  Member of University of North Texas, Team S4-G1, Thompson Spring 2018 



                    UNT-THOMPSON-S18S4G1                     


                                            5 Members                     


                                            16 Guides authored