Difficulty
Moderate
Steps
8
Time Required
35 minutes
Sections
3
- Back Cover
- 3 steps
- LCD
- 2 steps
- Motherboard
- 3 steps
Flags
0
BackNikon Coolpix S33
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Cover
- Remove battery before initiating this step to avoid the possibility of electric shock.
- Remove all four T5 Torx screws from the exterior of the camera.
- Remove all three T5 Torx screws located at the bottom of the camera next to the battery compartment.
Remove battery before initiating this step to avoid the possibility of electric shock.
Remove all four T5 Torx screws from the exterior of the camera.
Remove all three T5 Torx screws located at the bottom of the camera next to the battery compartment.
1024
Step 2
- Remove the two screws located above the HDMI and USB logos that are inside the camera’s battery compartment using a JIS000 screwdriver.
Remove the two screws located above the HDMI and USB logos that are inside the camera’s battery compartment using a JIS000 screwdriver.
Step 3
- Using a plastic opening tool, gently remove the back cover from the camera.
Using a plastic opening tool, gently remove the back cover from the camera.
Step 4
LCD
- Be sure to have followed the steps to remove the Back Cover of your camera before beginning to replace the LCD Screen. This guide will cover just the replacement of the LCD Screen.
- Using a plastic opening tool, pry the LCD screen out of its slot inside of the camera.
Be sure to have followed the steps to remove the Back Cover of your camera before beginning to replace the LCD Screen. This guide will cover just the replacement of the LCD Screen.
Using a plastic opening tool, pry the LCD screen out of its slot inside of the camera.
Step 5
- Before pulling the LCD Screen out of the camera, you will need to disconnect the ribbon connector that attaches the screen to the camera.
- Gently pull the ribbon connector out of it’s slot. You should be able to remove it without the need of any tools.
Before pulling the LCD Screen out of the camera, you will need to disconnect the ribbon connector that attaches the screen to the camera.
Gently pull the ribbon connector out of it’s slot. You should be able to remove it without the need of any tools.
Step 6
Motherboard
- Remove all three 15’’ Torx screws. Gently pry off the LCD holder using a plastic opening tool.
- Peel off the connecting tape under the LCD holder to disconnect it completely.
Remove all three 15’’ Torx screws. Gently pry off the LCD holder using a plastic opening tool.
Peel off the connecting tape under the LCD holder to disconnect it completely.
Step 7
- Peel back black electrical tape and disconnect the ribbon connectors from the mother board.
- Disconect the wires from the motherboard.
- Take out the two 15’’ Phillips screws, as shown in the image, using a Phillips screwdriver.
Peel back black electrical tape and disconnect the ribbon connectors from the mother board.
Disconect the wires from the motherboard.
Take out the two 15’’ Phillips screws, as shown in the image, using a Phillips screwdriver.
Step 8
- Gently pry off the motherboard using a plastic opening tool.
Gently pry off the motherboard using a plastic opening tool.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
5 other people completed this guide.
Author
with 3 other contributors
Maria Frias
Member since: 02/18/2016
564 Reputation
4 Guides authored
Badges:
14
+11 more badges
Team
USF Tampa, Team 16-3, Blackwell Winter 2016
Member of USF Tampa, Team 16-3, Blackwell Winter 2016
USFT-BLACKWELL-W16S16G3
3 Members
10 Guides authored
