Difficulty
Moderate
Steps
7
Time Required
10 minutes
Sections
2
- Nikon Coolpix S3100 disassembly
- 3 steps
- LCD Screen
- 4 steps
Flags
0
BackNikon Coolpix S3100 Camera
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Nikon Coolpix S3100 disassembly
- Remove 8-2.46 mm screws from both sides and bottom of camera using a #000 Phillips screwdriver.
- Remove 2 screws from left side. (picture 1)
- Remove 4 screws from bottom. (picture 2)
- Remove 2 screws from right side. (picture 3)
Remove 8-2.46 mm screws from both sides and bottom of camera using a #000 Phillips screwdriver.
Remove 2 screws from left side. (picture 1)
Remove 4 screws from bottom. (picture 2)
Remove 2 screws from right side. (picture 3)
1024
Step 2
- Remove black cover pulling up with left thumb. Hold silver cover with right thumb.
- Remove silver cover lifting up with left thumb. Hold the camera with right thumb.
- Once internal circuit board is exposed, the red and blue wire terminals at top center can provide a nasty shock from the charged flash capacitor (silver can to left of terminals). BE CAREFUL!
Remove black cover pulling up with left thumb. Hold silver cover with right thumb.
Remove silver cover lifting up with left thumb. Hold the camera with right thumb.
Once internal circuit board is exposed, the red and blue wire terminals at top center can provide a nasty shock from the charged flash capacitor (silver can to left of terminals). BE CAREFUL!
Step 3
- Remove 2-2.10mm screws in the front of the camera using a #000 Phillips screwdriver.
- Remove the two screws.
- Gently pull up to detach the frame. (picture 2)
Remove 2-2.10mm screws in the front of the camera using a #000 Phillips screwdriver.
Remove the two screws.
Gently pull up to detach the frame. (picture 2)
Step 4
LCD Screen
- Remove 2-2.10mm screws using a #000 Phillips screwdriver.
Remove 2-2.10mm screws using a #000 Phillips screwdriver.
Step 5
- Gently pull the orange board to the right.
Gently pull the orange board to the right.
Step 6
- Lift screen up holding both corners.
Lift screen up holding both corners.
Step 7
- Gently pull to the left to release from ZIF connector.
Gently pull to the left to release from ZIF connector.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 2 other contributors
Jorge
Member since: 03/11/2015
1,170 Reputation
7 Guides authored
Badges:
13
+10 more badges
Team
Colorado Springs, Team 2-4, Panko Spring 2015
Member of Colorado Springs, Team 2-4, Panko Spring 2015
UCCS-PANKO-S15S2G4
2 Members
13 Guides authored
Sindento 1 - Aug 7, 2015
Reply
No mention of getting an electric shock while removing the case.Bit of a tingle anyway.I held the camera in a plastic bag after that.
Anirban Bhattacharyya - Aug 27, 2016
Reply
This will probably not be replied to, but is there any reliable way to discharge the flash capacitor? Got shocked once, but I thought it was already discharged lol.
gary.grant - Apr 28, 2017
Reply
Connect a 1k ohm resister between the black and red wire from the capacitor. Give it a few moments to discharge through the resistor. Don’t discharge the capacitor without a resistor as you run a good chance of destroying the electronics. Wear your latex gloves too.
Janet Miles - Jan 12, 2018
Reply
Easy to follow