Difficulty
Moderate
Steps
9
Time Required
30 minutes - 1 hour
Sections
2
- Nikon Coolpix S3100 disassembly
- 3 steps
- Nikon Coolpix S3100 Camera Disassembly
- 6 steps
Flags
0
BackNikon Coolpix S3100 Camera
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Nikon Coolpix S3100 disassembly
- Remove 8-2.46 mm screws from both sides and bottom of camera using a #000 Phillips screwdriver.
- Remove 2 screws from left side. (picture 1)
- Remove 4 screws from bottom. (picture 2)
- Remove 2 screws from right side. (picture 3)
Remove 8-2.46 mm screws from both sides and bottom of camera using a #000 Phillips screwdriver.
Remove 2 screws from left side. (picture 1)
Remove 4 screws from bottom. (picture 2)
Remove 2 screws from right side. (picture 3)
1024
Step 2
- Remove black cover pulling up with left thumb. Hold silver cover with right thumb.
- Remove silver cover lifting up with left thumb. Hold the camera with right thumb.
- Once internal circuit board is exposed, the red and blue wire terminals at top center can provide a nasty shock from the charged flash capacitor (silver can to left of terminals). BE CAREFUL!
Remove black cover pulling up with left thumb. Hold silver cover with right thumb.
Remove silver cover lifting up with left thumb. Hold the camera with right thumb.
Once internal circuit board is exposed, the red and blue wire terminals at top center can provide a nasty shock from the charged flash capacitor (silver can to left of terminals). BE CAREFUL!
Step 3
- Remove 2-2.10mm screws in the front of the camera using a #000 Phillips screwdriver.
- Remove the two screws.
- Gently pull up to detach the frame. (picture 2)
Remove 2-2.10mm screws in the front of the camera using a #000 Phillips screwdriver.
Remove the two screws.
Gently pull up to detach the frame. (picture 2)
Step 4
Nikon Coolpix S3100 Camera Disassembly
- Remove 2-2.10mm screws using a #000 Phillips screwdriver.
- Gently pull the orange board to the right. (picture 2)
Remove 2-2.10mm screws using a #000 Phillips screwdriver.
Gently pull the orange board to the right. (picture 2)
Step 5
- Lift screen up holding the corners.
- Gently pull to the left to release from ZIF connector. (picture 2)
- Gently pull the orange board to the right. (picture 3)
Lift screen up holding the corners.
Gently pull to the left to release from ZIF connector. (picture 2)
Gently pull the orange board to the right. (picture 3)
Step 6
- Remove 4-2.10mm screws using a #000 Phillips screwdriver.
- Gently pull the shutter up. (picture 2)
Remove 4-2.10mm screws using a #000 Phillips screwdriver.
Gently pull the shutter up. (picture 2)
Step 7
- Lens is now separated from body.
- Remove 3-2.12mm screws using #000 Phillips screwdriver.
Lens is now separated from body.
Remove 3-2.12mm screws using #000 Phillips screwdriver.
Step 8
- Use a nylon or metal spudger to release the lens.
- Repeat step 4 to the opposite side of the lens. (picture 2)
- Lens is now separated from metal.
Use a nylon or metal spudger to release the lens.
Repeat step 4 to the opposite side of the lens. (picture 2)
Lens is now separated from metal.
Step 9
- Once you have all the parts separated, start cleaning them with an air compressor bottle. (as shown)
- Using the provided straw, start spraying the parts. (pictures 2 and 3)
Once you have all the parts separated, start cleaning them with an air compressor bottle. (as shown)
Using the provided straw, start spraying the parts. (pictures 2 and 3)
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 4 other contributors
Jorge
Member since: 03/11/2015
1,170 Reputation
7 Guides authored
Badges:
13
+10 more badges
Team
Colorado Springs, Team 2-4, Panko Spring 2015
Member of Colorado Springs, Team 2-4, Panko Spring 2015
UCCS-PANKO-S15S2G4
2 Members
13 Guides authored