Featured
Featured Guide
Difficulty
Moderate
Steps
8
Time Required
Suggest a time??
Sections
3
- Battery
- 2 steps
- Back Case
- 4 steps
- LCD screen
- 2 steps
Flags
1
Featured Guide
This guide has been found to be exceptionally cool by the iFixit staff.
BackNikon Coolpix S210
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Place thumb on the battery cover panel on the bottom of the device.
- Slide the panel to the right away from the camera.
Place thumb on the battery cover panel on the bottom of the device.
Slide the panel to the right away from the camera.
1024
Step 2
- Slide the orange latch outward towards the corner of the camera.
- The battery should pop out.
- Remove the battery and reattach the cover.
Slide the orange latch outward towards the corner of the camera.
The battery should pop out.
Remove the battery and reattach the cover.
Step 3
Back Case
- After removing the battery, unscrew the four 3.10mm screws on the side opposite the buttons.
After removing the battery, unscrew the four 3.10mm screws on the side opposite the buttons.
Step 4
- Unscrew the three 4.05mm screws on the bottom of the camera below the lens.
Unscrew the three 4.05mm screws on the bottom of the camera below the lens.
Step 5
- Unscrew the two 4.05mm screws on the side next to the buttons.
Unscrew the two 4.05mm screws on the side next to the buttons.
Step 6
- Gently wedge the flat end of the spudger between the back case and the wrist-strap mount.
- The wrist-strap mount is the thin metal piece on the side of the camera. Your camera may have the wrist-strap attached, but you will not need to remove it to continue.
- Carefully pry the back case away from the camera and then gently lift it off.
Gently wedge the flat end of the spudger between the back case and the wrist-strap mount.
The wrist-strap mount is the thin metal piece on the side of the camera. Your camera may have the wrist-strap attached, but you will not need to remove it to continue.
Carefully pry the back case away from the camera and then gently lift it off.
Step 7
LCD screen
- Having removed the back case, the LCD screen should be sitting loosely on the camera, attached only by a wide ribbon and a narrow ribbon.
- The ribbons are connected to and held in place by small plastic latches.
- To remove the wide ribbon, gently pry the spudger underneath the black plastic latch where the ribbon connects and lift up. The ribbon should slide out easily.
- Repeat the same process with the smaller ribbon, this time looking for a light blue latch.
Having removed the back case, the LCD screen should be sitting loosely on the camera, attached only by a wide ribbon and a narrow ribbon.
The ribbons are connected to and held in place by small plastic latches.
To remove the wide ribbon, gently pry the spudger underneath the black plastic latch where the ribbon connects and lift up. The ribbon should slide out easily.
Repeat the same process with the smaller ribbon, this time looking for a light blue latch.
Step 8
- Gently remove the LCD screen.
Gently remove the LCD screen.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 7 other contributors
Mallory Arend
Member since: 01/17/2011
444 Reputation
2 Guides authored
Badges:
10
+7 more badges
Team
Cal Poly, Team 5-17, Amido Winter 2011
Member of Cal Poly, Team 5-17, Amido Winter 2011
CPSU-AMIDO-W11S5G17
6 Members
12 Guides authored
geral - Apr 8, 2016
Reply
Funcionou conforme descrito! Funciona para a Nikon Coolpix S203