Difficulty

Moderate

Steps

9

Time Required

                          30 - 45 minutes

Sections

2

  • Back Casing
  • 7 steps
  • Multi Selector Wheel
  • 2 steps

Flags

1

Bullets!

Better coordination with markups and the color/type of bullets will help make this guide more clear!

  • BackNikon COOLPIX P7700

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Casing
  • Turn camera to the left side and remove the two 4.3 mm black side screws using the Phillips #00 screwdriver.
  • Remove the side panel.

Turn camera to the left side and remove the two 4.3 mm black side screws using the Phillips #00 screwdriver.

Remove the side panel.

1024

Step 2

  • Open the touch screen, and remove the three 4.3 mm black screws inside using the Phillips #00 screwdriver.

Open the touch screen, and remove the three 4.3 mm black screws inside using the Phillips #00 screwdriver.

Step 3

  • Remove the 4.3 mm black screw on top of the camera, right above where the screen folds out. Use the Phillips #00 screwdriver.

Remove the 4.3 mm black screw on top of the camera, right above where the screen folds out. Use the Phillips #00 screwdriver.

Step 4

  • Remove the two 4.3 mm black screws on the right side of the camera using the Phillips #00 screwdriver.

Remove the two 4.3 mm black screws on the right side of the camera using the Phillips #00 screwdriver.

Step 5

  • Remove the 4.3 mm black screws on the bottom of the camera using the Phillips #00 screwdriver.

Remove the 4.3 mm black screws on the bottom of the camera using the Phillips #00 screwdriver.

Step 6

  • Begin separating the camera into two parts.
  • It is okay to remove the orange ribbon. This will be easily put back into place when re-assembling.

Begin separating the camera into two parts.

It is okay to remove the orange ribbon. This will be easily put back into place when re-assembling.

Step 7

  • Remove the back casing.

Remove the back casing.

Step 8

              Multi Selector Wheel
  • Remove the four 4.3 mm screws located on the far right metal plate. Use the Phillips #00 screwdriver.

Remove the four 4.3 mm screws located on the far right metal plate. Use the Phillips #00 screwdriver.

Step 9

  • Remove and replace wheel.

Remove and replace wheel.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      7 other people completed this guide.

Author

                                      with 2 other contributors 


                    Dustin Wahl

Member since: 03/11/2015

775 Reputation

                                      4 Guides authored                  



                       Badges:
                       14







                                                        +11 more badges

Team

                       Colorado Springs, Team 2-7, Panko Spring 2015                        

                                                  Member of Colorado Springs, Team 2-7, Panko Spring 2015 



                    UCCS-PANKO-S15S2G7                     


                                            3 Members                     


                                            10 Guides authored

basstrom - Sep 20, 2015

Reply

Step 9: I believe that the multi-selector wheel component is soldered, 3 wires just visible in the photo for step 8. This will surely add to the time taken and difficulty.

I have a problem with this component. Firstly it’s almost impossible to obtain the replacement parts, but if I could this guide would be invaluable; pictures are worth a thousand words! Thanks.

fiteluetkehoff - Mar 31, 2016

Reply

where can I get the item ( wheel ) ?

Best regards and thank you for the good explanation

skromnjagaserj - Jul 12, 2016

Reply

Where i can find this wheel for replacement?

JY - Nov 13, 2016

Reply

JY - Feb 16, 2017

Reply