Nikon Coolpix P530 Ccd Sensor Replacement Repair Guide

Difficulty

Easy

Steps

Time Required

                          8 minutes

Sections

Battery
4 steps
Back Cover
5 steps
LCD
2 steps
LCD Bracket
2 steps
CCD Sensor
3 steps

Flags

BackNikon Coolpix P530
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Identify the battery chamber found at the bottom of the device.
Ensure the camera is turned off before conducting any maintenance on the device.

Identify the battery chamber found at the bottom of the device.

Ensure the camera is turned off before conducting any maintenance on the device.

1024

Step 2

Slide the switch to the left to open the battery chamber using your fingertip or plastic opening tools.
The spring loaded battery chamber door will swing open after the switch is moved.

Slide the switch to the left to open the battery chamber using your fingertip or plastic opening tools.

The spring loaded battery chamber door will swing open after the switch is moved.

Step 3

Depress the yellow spring loaded tab holding the battery in place using your fingertip or plastic opening tools.
After the yellow tab is depressed, the battery should partially eject from the camera.

Depress the yellow spring loaded tab holding the battery in place using your fingertip or plastic opening tools.

After the yellow tab is depressed, the battery should partially eject from the camera.

Step 4

Gently remove the battery from the chamber.

Gently remove the battery from the chamber.

Step 5

              Back Cover

Remove the six 4mm screws highlighted in red with the Phillips #000 screwdriver.
Remove the 5mm screw highlighted in orange with the Phillips #000 screwdriver.

Remove the six 4mm screws highlighted in red with the Phillips #000 screwdriver.

Remove the 5mm screw highlighted in orange with the Phillips #000 screwdriver.

Step 6

Pop up the camera flash using the button below the lightning bolt on the left side of the camera.
Identify the small notch below the camera flash where the body of the camera and the back cover join.
Use plastic opening tools to pry the darker plastic piece under the camera flash from the lighter plastic camera body.

Pop up the camera flash using the button below the lightning bolt on the left side of the camera.

Identify the small notch below the camera flash where the body of the camera and the back cover join.

Use plastic opening tools to pry the darker plastic piece under the camera flash from the lighter plastic camera body.

Step 7

Gently pry with a plastic opening tool around the perimeter of the camera.
The plastic HDMI cover can become loose and fall off during this step. Once the back cover is free from the camera you may remove this piece to store in a safe place.

Gently pry with a plastic opening tool around the perimeter of the camera.

The plastic HDMI cover can become loose and fall off during this step. Once the back cover is free from the camera you may remove this piece to store in a safe place.

Step 8

Gently lift the back cover away from the camera body.
A gold ribbon cable will join the back cover of the camera to the internal electronic components. Be careful not to remove the back cover without removing the cable since this part can easily break.
To remove the ribbon cable, gently pull the connector from the camera’s internal electronic components using a pair of tweezers.
Flip the orange bar securing the ribbon cable upwards to allow for safe removal.

Gently lift the back cover away from the camera body.

A gold ribbon cable will join the back cover of the camera to the internal electronic components. Be careful not to remove the back cover without removing the cable since this part can easily break.

To remove the ribbon cable, gently pull the connector from the camera’s internal electronic components using a pair of tweezers.

Flip the orange bar securing the ribbon cable upwards to allow for safe removal.

Step 9

After the ribbon cable is removed from the camera body, the cover can be completely removed.

After the ribbon cable is removed from the camera body, the cover can be completely removed.

Step 10

LCD

Lift the LCD screen upwards.

Lift the LCD screen upwards.

Step 11

Tilt the screen towards the ribbon cable.
Remove the ribbon cable by gently pulling the cable away from the motherboard using tweezers.
Flip the orange bar securing the ribbon cable upwards to allow for safe removal.

Tilt the screen towards the ribbon cable.

Remove the ribbon cable by gently pulling the cable away from the motherboard using tweezers.

Step 12

              LCD Bracket

Remove the six 4mm screws highlighted in red using the Philips #000 screwdriver.
Remove the 6mm screw highlighted in orange using the Philips #000 screwdriver.
One of the 4mm screws is on the exterior of the device.

Remove the six 4mm screws highlighted in red using the Philips #000 screwdriver.

Remove the 6mm screw highlighted in orange using the Philips #000 screwdriver.

One of the 4mm screws is on the exterior of the device.

Step 13

Lift and remove the LCD mounting bracket to expose underlying hardware.

Lift and remove the LCD mounting bracket to expose underlying hardware.

Step 14

              CCD Sensor

Disconnect the ribbon cable connector by prying upwards on the part using the plastic opening tools.

Disconnect the ribbon cable connector by prying upwards on the part using the plastic opening tools.

Step 15

Remove the 3mm screws highlighted in red using the Philips #000 screwdriver.
There should be a total of three screws removed in this step.

Remove the 3mm screws highlighted in red using the Philips #000 screwdriver.

There should be a total of three screws removed in this step.

Step 16

Use the tweezers to remove the CCD sensor carefully.

Use the tweezers to remove the CCD sensor carefully.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 3 other contributors

                    Alan Weihe

Member since: 02/01/2016

980 Reputation

                                      7 Guides authored                  



                       Badges:
                       17







                                                        +14 more badges

Team

                       University of Kentucky Louisville, Team 1-2, Matravers Spring 2016                        

                                                  Member of University of Kentucky Louisville, Team 1-2, Matravers Spring 2016 



                    LOUISVILLE-MATRAVERS-S16S1G2                     


                                            3 Members                     


                                            14 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team