Difficulty
Moderate
Steps
10
Time Required
Suggest a time??
Sections
1
- Lens Assembly
- 10 steps
Flags
0
BackNikon Coolpix P510
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Lens Assembly
- Flip the camera upside down and remove six 3mm PH00 Philips screws with a Philips screwdriver.
- On the thumb grip, remove the one 4mm PH00 Philips screw.
Flip the camera upside down and remove six 3mm PH00 Philips screws with a Philips screwdriver.
On the thumb grip, remove the one 4mm PH00 Philips screw.
1024
Step 2
- With the camera upside down, remove the three 3mm PH00 Philips screws on the left side.
- One of the screws are under the HDMI and A/V Out cover.
With the camera upside down, remove the three 3mm PH00 Philips screws on the left side.
One of the screws are under the HDMI and A/V Out cover.
Step 3
- On the opposite side of the camera, remove the two 3mm PH00 Philips screws.
On the opposite side of the camera, remove the two 3mm PH00 Philips screws.
Step 4
- Open the flash and use a plastic opening tool to pop the tab under it as shown.
- Now pull the casing apart.
- The tripod attachment may fall out on its own, or you will need to pull it out.
Open the flash and use a plastic opening tool to pop the tab under it as shown.
Now pull the casing apart.
The tripod attachment may fall out on its own, or you will need to pull it out.
Step 5
- Unplug the two ribbon cables to completely detach the back.
Unplug the two ribbon cables to completely detach the back.
Step 6
- With the back separated, you need to remove six 3mm PH000 Philips screws with a Philips screwdriver.
- Remove one 5mm PH00 Philips screw
- To remove the top right corner screw, you may need to lift the corner of the case to gain access to it.
- With all the screws out, the metal plate should simply lift off.
With the back separated, you need to remove six 3mm PH000 Philips screws with a Philips screwdriver.
Remove one 5mm PH00 Philips screw
To remove the top right corner screw, you may need to lift the corner of the case to gain access to it.
With all the screws out, the metal plate should simply lift off.
Step 7
- With the metal plate off, unplug this ribbon cable from the motherboard.
- To remove the flat-topped connector, you simply lift it up to unplug it.
With the metal plate off, unplug this ribbon cable from the motherboard.
To remove the flat-topped connector, you simply lift it up to unplug it.
Step 8
- To get the lens assembly out, you need to remove four 6mm PH00 Philips screws
To get the lens assembly out, you need to remove four 6mm PH00 Philips screws
Step 9
- With the support screws out, you can simply slide the assembly out of the casing.
With the support screws out, you can simply slide the assembly out of the casing.
Step 10
- If you are moving on to take the lens casing off, you do not need to do this step.
- With the assembly out we need to take of this last piece by removing the three 3mm PH000 Philips screws.
If you are moving on to take the lens casing off, you do not need to do this step.
With the assembly out we need to take of this last piece by removing the three 3mm PH000 Philips screws.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
9 other people completed this guide.
Author
with 3 other contributors
Brian Hulsey
Member since: 03/31/2015
1,410 Reputation
6 Guides authored
Badges:
13
+10 more badges
Team
Colorado Springs, Team 2-2, Panko Spring 2015
Member of Colorado Springs, Team 2-2, Panko Spring 2015
UCCS-PANKO-S15S2G2
3 Members
12 Guides authored
