Featured
Featured Guide
Difficulty
Moderate
Steps
15
Time Required
5 minutes
Sections
2
- Battery
- 2 steps
- LCD Screen
- 13 steps
Flags
3
Bullets!
Better coordination with markups and the color/type of bullets will help make this guide more clear!
Featured Guide
This guide has been found to be exceptionally cool by the iFixit staff.
Better Introduction
Improve this guide by completing or revising its introduction.
BackNikon Coolpix P4
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- ‘Click’ the battery door over to the side.
‘Click’ the battery door over to the side.
1024
Step 2
- Open the battery door. Inside is the memory card and the battery.
- Click over the orange tab and take out the battery.
- Close the battery lid by pushing it down and sliding it back.
Open the battery door. Inside is the memory card and the battery.
Click over the orange tab and take out the battery.
Close the battery lid by pushing it down and sliding it back.
Step 3
LCD Screen
- Remove the four screws located on bottom of camera. (.086in screws)
Remove the four screws located on bottom of camera. (.086in screws)
Step 4
- Remove the two screws, then remove the panel. (.113in screws)
Remove the two screws, then remove the panel. (.113in screws)
Step 5
- Remove panel on right side (front view) by removing these two screws. (.196in screws)
- Remove single screw set underneath panel. (0.083in screw)
Remove panel on right side (front view) by removing these two screws. (.196in screws)
Remove single screw set underneath panel. (0.083in screw)
Step 6
- Remove the two screws attaching the back panel to the body on the left side. (.188in screws)
Remove the two screws attaching the back panel to the body on the left side. (.188in screws)
Step 7
- Gently pull off back cover
Gently pull off back cover
Step 8
- Then remove the three screws on the A/V Out tab (left side). (.188in screws)
- Remove tab.
Then remove the three screws on the A/V Out tab (left side). (.188in screws)
Remove tab.
Step 9
- Remove the two screws attaching the front panel to the body on the left side. (.18in screws)
Remove the two screws attaching the front panel to the body on the left side. (.18in screws)
Step 10
- Flip up front panel.
- There should be wires still attaching the panel to body. DO NOT TRY TO PULL OFF COMPLETELY
Flip up front panel.
There should be wires still attaching the panel to body. DO NOT TRY TO PULL OFF COMPLETELY
Step 11
- Remove three screws as shown. (Right screw:0.084in, Left screw:0.088in, Middle screw:0.114in)
Remove three screws as shown. (Right screw:0.084in, Left screw:0.088in, Middle screw:0.114in)
Step 12
- Carefully pull orange LCD connector up and out of the port.
- Be careful to pull vertically while pushing the black tab upwards
Carefully pull orange LCD connector up and out of the port.
Be careful to pull vertically while pushing the black tab upwards
Step 13
- Remove the screw below the LCD (.124in)
Remove the screw below the LCD (.124in)
Step 14
- Carefully pull out the plug connecting the LCD to the motherboard.
Carefully pull out the plug connecting the LCD to the motherboard.
Step 15
- You can now remove the LCD from the camera body.
- Insert new LCD and reassemble using the steps in reverse order.
You can now remove the LCD from the camera body.
Insert new LCD and reassemble using the steps in reverse order.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 9 other contributors
Luke Baumann
Member since: 04/13/2011
128 Reputation
5 Guides authored
Badges:
10
+7 more badges
Team
Cal Poly, Team 8-5, Regan Spring 2011
Member of Cal Poly, Team 8-5, Regan Spring 2011
CPSU-REGAN-S11S8G5
4 Members
10 Guides authored