Difficulty

Difficult

Steps

12

Time Required

                          20 - 25 minutes

Sections

2

  • LCD
  • 7 steps
  • Motherboard
  • 5 steps

Flags

0

  • BackNikon Coolpix L810

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              LCD
  • Remove two 5 mm Phillips #000 screws on the right hand side of the camera located near the power button.
  • Use of precision tweezers to help remove loosened screws is suggested.

Remove two 5 mm Phillips #000 screws on the right hand side of the camera located near the power button.

Use of precision tweezers to help remove loosened screws is suggested.

1024

Step 2

  • Remove two 5 mm Phillips #000 screws near the audio/video inputs on the opposite side near the flash component.

Remove two 5 mm Phillips #000 screws near the audio/video inputs on the opposite side near the flash component.

Step 3

  • Remove three 5 mm Phillips #000 screws on the bottom end of the camera.

Remove three 5 mm Phillips #000 screws on the bottom end of the camera.

Step 4

  • Carefully detach the back side of the camera by lifting both ends, with moderate force wobble until loosened enough to remove.

Carefully detach the back side of the camera by lifting both ends, with moderate force wobble until loosened enough to remove.

Step 5

  • With the LCD screen facing towards you, flip the screen to the right.

With the LCD screen facing towards you, flip the screen to the right.

Step 6

  • Remove three 5 mm Phillips #000 screws located on the bracket.
  • Hold the camera with the lens facing downward to prevent the bracket from falling off once all screws are removed.

Remove three 5 mm Phillips #000 screws located on the bracket.

Hold the camera with the lens facing downward to prevent the bracket from falling off once all screws are removed.

Step 7

  • Disconnect the ribbons that connect the LCD screen to the camera gently using precision tweezers or fingers.

Disconnect the ribbons that connect the LCD screen to the camera gently using precision tweezers or fingers.

Step 8

              Motherboard
  • Remove three 5 mm Phillips #000 screws bordering the motherboard.

Remove three 5 mm Phillips #000 screws bordering the motherboard.

Step 9

  • Remove the plastic component located directly behind the flash from its rubberized holder.

Remove the plastic component located directly behind the flash from its rubberized holder.

Step 10

  • Remove the electric tape covering the wires.

Remove the electric tape covering the wires.

Step 11

  • Unsolder all the wires that are on the top of the motherboard near the flash component.

Unsolder all the wires that are on the top of the motherboard near the flash component.

Step 12

  • Unsolder the wires on the bottom end of the motherboard.

Unsolder the wires on the bottom end of the motherboard.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 2 other contributors 


                    Emilio Mena

Member since: 01/14/2015

725 Reputation

                                      4 Guides authored                  



                       Badges:
                       13







                                                        +10 more badges

Team

                       UW Tacoma, Team 3-1, Rose Winter 2015                        

                                                  Member of UW Tacoma, Team 3-1, Rose Winter 2015 



                    UWT-ROSE-W15S3G1                     


                                            4 Members                     


                                            8 Guides authored

symeonleriou - Sep 22, 2016

Reply

The guide is incomplete! Do not try to remove the mobo for it is soldered to some other tiny board under the on/off switch. Trying to remove the mobo after just unscrewing it, may guide to certain and permanent destruction of both PCBs!!!

jon baker - Mar 31, 2017

Reply

any clue how to get tiny mobo out with mobo after taking screw out of tiny one at on/off switch?

lothar4460 - Apr 25, 2020

Reply

This guide should be for beginners, Mr. Symeon Leriou, and you will not only write “Mobo”, but also motherboard or Mainboard or Hauptplatine (deutsch)

But I agree with you that it is not complete.

The motherboard is soldered to the on / off board (power supply for the batteries).

Soldering again is almost impossible …

ramos.eng - May 5, 2020

Reply

Exactly! The guide is GOOD but it is incomplete!

The solder removal is insufficient to release de motherboard.

How to do it?