Difficulty

Difficult

Steps

12

Time Required

Suggest a time??

Sections

4

  • Plastic Cover
  • 4 steps
  • Control Panel
  • 2 steps
  • LCD Screen
  • 2 steps
  • Camera Lens
  • 4 steps

Flags

0

  • BackNikon Coolpix L610

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Plastic Cover
  • Remove the four (3.20 mm) Phillips #00 screws at the bottom of the device.

Remove the four (3.20 mm) Phillips #00 screws at the bottom of the device.

1024

Step 2

  • Remove the top (4.10 mm) Phillips #00 screw adjacent to the battery compartment.
  • Remove the bottom (3.20 mm) Phillips #00 screw adjacent to the battery compartment.

Remove the top (4.10 mm) Phillips #00 screw adjacent to the battery compartment.

Remove the bottom (3.20 mm) Phillips #00 screw adjacent to the battery compartment.

Step 3

  • Remove the top (4.20 mm) Phillips #00 screw adjacent to the mic side of the camera and opposite the battery side.
  • Remove the lower (3.20 mm) Phillips #00 screw adjacent to the mic side of the camera and opposite of the battery side.

Remove the top (4.20 mm) Phillips #00 screw adjacent to the mic side of the camera and opposite the battery side.

Remove the lower (3.20 mm) Phillips #00 screw adjacent to the mic side of the camera and opposite of the battery side.

Step 4

  • Separate the case using the plastic prying tool. This can be done by placing the tool in the position that is shown and in the position on the left side of the camera.

Separate the case using the plastic prying tool. This can be done by placing the tool in the position that is shown and in the position on the left side of the camera.

Step 5

              Control Panel
  • Carefully unscrew and remove the top and bottom (2.25 mm) screws from the control panel.
  • Carefully unscrew and remove the middle (3.20 mm) screws from the control panel.

Carefully unscrew and remove the top and bottom (2.25 mm) screws from the control panel.

Carefully unscrew and remove the middle (3.20 mm) screws from the control panel.

Step 6

  • Carefully remove the ribbon connecting the control panel to the camera. The latch can be removed by sliding it down and pulling the ribbon down.

Carefully remove the ribbon connecting the control panel to the camera. The latch can be removed by sliding it down and pulling the ribbon down.

Step 7

              Removing the screen
  • Using a prying tool, carefully lift up the LCD screen but do NOT pull it off.

Using a prying tool, carefully lift up the LCD screen but do NOT pull it off.

Step 8

              Removing the LCD Screen Ribbon
  • While the LCD screen is loose and unattached, there is a latch that is holding the ribbon in place. Slide the latch down and pull the ribbon out.

While the LCD screen is loose and unattached, there is a latch that is holding the ribbon in place. Slide the latch down and pull the ribbon out.

Step 9

              Camera Lens
  • Remove the 6 (3.70 mm) screws on the metal cover. Two of those screws are covered by black plastic covers.
  • After removing the screws the panel should come off and will look like the final image.
  • Be careful of the red and black wires on the top. If the flash is charged you could get a mild shock.

Remove the 6 (3.70 mm) screws on the metal cover. Two of those screws are covered by black plastic covers.

After removing the screws the panel should come off and will look like the final image.

Be careful of the red and black wires on the top. If the flash is charged you could get a mild shock.

Step 10

  • Unplug the two ribbons for the lens. There will be latch that will need to be slid down. After loosening the latch, the ribbon should be able to be easily pulled out.

Unplug the two ribbons for the lens. There will be latch that will need to be slid down. After loosening the latch, the ribbon should be able to be easily pulled out.

Step 11

  • Remove the 3 (3.10 mm) screws that are located on the back of the lens cover.

Remove the 3 (3.10 mm) screws that are located on the back of the lens cover.

Step 12

  • There are two lens covers that will fall out after removing the back lens plate.
  • Remove the 6 (4.35 mm) screws surrounding the lens.
  • There are 2 more (3.70 mm) screws covered by a small black square located. Remove the black squares and proceed to unscrewing these final screws.
  • Remove the lens. It should just be free to pull it out.

There are two lens covers that will fall out after removing the back lens plate.

Remove the 6 (4.35 mm) screws surrounding the lens.

There are 2 more (3.70 mm) screws covered by a small black square located. Remove the black squares and proceed to unscrewing these final screws.

Remove the lens. It should just be free to pull it out.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 5 other contributors 


                    Jeremy

Member since: 01/21/2015

982 Reputation

                                      5 Guides authored                  



                       Badges:
                       18







                                                        +15 more badges

Team

                       USF Tampa, Team 9-4, Brown Winter 2015                        

                                                  Member of USF Tampa, Team 9-4, Brown Winter 2015 



                    USFT-BROWN-W15S9G4                     


                                            4 Members                     


                                            12 Guides authored