Difficulty
Difficult
Steps
7
Time Required
30 - 50 minutes
Sections
2
- Back Housing
- 2 steps
- Front Housing
- 5 steps
Flags
0
BackNikon Coolpix L330
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Housing
- There are six screws attaching the back housing to the camera. Remove the screws from the body with a PH000 screw head.
- Two 1.5x2.5mm screws on the right side.
- Two 1.5x2.5mm screws on the underside.
- Two 1.5x2.5mm screw on the left side.
There are six screws attaching the back housing to the camera. Remove the screws from the body with a PH000 screw head.
Two 1.5x2.5mm screws on the right side.
Two 1.5x2.5mm screws on the underside.
Two 1.5x2.5mm screw on the left side.
1024
Step 2
- After removing the screws, use a metal spudger or plastic opening tool to push the back cover out.
- The metal spudger can damage the plastic housing, so use caution when applying any pressure to it. Use a plastic opening tool to reduce the risk of damage to the housing.
- Remove the back housing of the camera by lifting it directly up.
- The back cover may be slightly tight, therefore more force may be needed to lift it up.
After removing the screws, use a metal spudger or plastic opening tool to push the back cover out.
The metal spudger can damage the plastic housing, so use caution when applying any pressure to it. Use a plastic opening tool to reduce the risk of damage to the housing.
Remove the back housing of the camera by lifting it directly up.
The back cover may be slightly tight, therefore more force may be needed to lift it up.
Step 3
Front Housing
- Remove the four 1.5x2.5mm screws in the battery housing using a PH000 screw head.
Remove the four 1.5x2.5mm screws in the battery housing using a PH000 screw head.
Step 4
- Remove the two 1.5x2.5mm screws below the flash unit using a PH000 screw head.
Remove the two 1.5x2.5mm screws below the flash unit using a PH000 screw head.
Step 5
- Remove the black tape covering the electrical connections.
- Remove the 1.5x2.5mm screw using a PH000 screw head.
- Desolder the six marked wires.
- The screen has been removed as well as the back-plate in this step, however they need not be removed to replace the front housing.
Remove the black tape covering the electrical connections.
Remove the 1.5x2.5mm screw using a PH000 screw head.
Desolder the six marked wires.
The screen has been removed as well as the back-plate in this step, however they need not be removed to replace the front housing.
Step 6
- Insert a plastic opening tool between the front housing and inner frame.
- Lever the tool to slide the front housing forward.
Insert a plastic opening tool between the front housing and inner frame.
Lever the tool to slide the front housing forward.
Step 7
- Position the fingers of one hand on the inner frame and the other hand around the lens barrel.
- Pull the front housing away from the inner frame.
Position the fingers of one hand on the inner frame and the other hand around the lens barrel.
Pull the front housing away from the inner frame.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Rajeev
Member since: 02/09/2016
569 Reputation
4 Guides authored
Badges:
11
+8 more badges
Team
USF Tampa, Team 2-10, Cagle Spring 2016
Member of USF Tampa, Team 2-10, Cagle Spring 2016
USFT-CAGLE-S16S2G10
4 Members
14 Guides authored
