Nikon Coolpix L26 Camera Front Cover Replacement Repair Guide

Difficulty

Moderate

Steps

14

Time Required

                          20 minutes            

Sections

3

• Back Cover
• 7 steps
• LCD Screen
• 5 steps
• Front Cover
• 2 steps

Flags

0

• BackNikon Coolpix L26

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Back Cover               

• Remove the batteries from the battery compartment by sliding the white battery compartment switch up and then move the panel toward the right.

Remove the batteries from the battery compartment by sliding the white battery compartment switch up and then move the panel toward the right.

1024

Step 2

• Using the Phillips #000 screwdriver, unscrew the two 2mm screws next to the battery compartment on the right side of the camera.

Using the Phillips #000 screwdriver, unscrew the two 2mm screws next to the battery compartment on the right side of the camera.

Step 3

• Unscrew the two 2mm screws on the opposite side.

Unscrew the two 2mm screws on the opposite side.

Step 4

• Flip over the rubber AV cover at the bottom of the camera. Unscrew the last two 2mm screws on the bottom of the camera.

Flip over the rubber AV cover at the bottom of the camera. Unscrew the last two 2mm screws on the bottom of the camera.

Step 5

• Using your hands, open the camera slightly by using the indentation above the camera compartment.

Using your hands, open the camera slightly by using the indentation above the camera compartment.

Step 6

• Wedge the flat end of the spudger in between the front and back cover. Carefully push the spudger downward, which will lift the back cover off the camera.

Wedge the flat end of the spudger in between the front and back cover. Carefully push the spudger downward, which will lift the back cover off the camera.

Step 7

• Gently pull the cover off the camera.

Gently pull the cover off the camera.

Step 8

              LCD Screen               

• Carefully flip over the LCD screen onto its front. Pull the top of the LCD screen toward you keeping the bottom of it inside the camera.
• Do not pull on the LCD screen; there is a ribbon of circuitry that is connected to the motherboard.

Carefully flip over the LCD screen onto its front. Pull the top of the LCD screen toward you keeping the bottom of it inside the camera.

Do not pull on the LCD screen; there is a ribbon of circuitry that is connected to the motherboard.

Step 9

• Gently hold the LCD screen down, so the ribbon lays flat against the back of the camera.

Gently hold the LCD screen down, so the ribbon lays flat against the back of the camera.

Step 10

• Gently wedge the spudger underneath the white latch and lift the latch open.

Gently wedge the spudger underneath the white latch and lift the latch open.

Step 11

• Use the flat side of the spudger to flip the white switch on the motherboard. You should hear a light click.

Use the flat side of the spudger to flip the white switch on the motherboard. You should hear a light click.

Step 12

• Gently pull the ribbon out of the switch.

Gently pull the ribbon out of the switch.

Step 13

              Front Cover               

• Open the battery compartment door by sliding the white switch upwards. Push the door towards the right of the camera.

Open the battery compartment door by sliding the white switch upwards. Push the door towards the right of the camera.

Step 14

• Hold the camera with the lens face down to prevent the plastic covers of the warning light and the flash bulb from falling out.
• Take a firm hold of the black inner casing of the top and bottom of internal camera. With your other hand, take a hold of the red front case.
• With slight force, pull the internal camera upwards and out of the front case.

Hold the camera with the lens face down to prevent the plastic covers of the warning light and the flash bulb from falling out.

Take a firm hold of the black inner casing of the top and bottom of internal camera. With your other hand, take a hold of the red front case.

With slight force, pull the internal camera upwards and out of the front case.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 3 other contributors 

                    Sadie                     

Member since: 02/16/2015

403 Reputation

                                      3 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges                           

Team

                       San Diego State, Team 1-3, Sheppard Winter 2015                        

                                                  Member of San Diego State, Team 1-3, Sheppard Winter 2015 



                    SDSU-SHEPPARD-W15S1G3                     


                                            2 Members                     


                                            6 Guides authored