Difficulty
Difficult
Steps
12
Time Required
40 minutes
Sections
3
- Battery
- 4 steps
- Back Panel
- 5 steps
- LCD Screen
- 3 steps
Flags
0
BackNikon Coolpix AW130
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Using your thumb and pointer finger, open the card/battery hatch by pressing the center button of the wheel and turning the entire wheel to the left.
- When reassembling, you must turn this wheel to the right until it clicks.
Using your thumb and pointer finger, open the card/battery hatch by pressing the center button of the wheel and turning the entire wheel to the left.
When reassembling, you must turn this wheel to the right until it clicks.
1024
Step 2
- You should feel the door begin to loosen. Carefully pull the hatch open.
You should feel the door begin to loosen. Carefully pull the hatch open.
Step 3
- Push the yellow battery/charger compartment tab up using your thumb nail.
Push the yellow battery/charger compartment tab up using your thumb nail.
Step 4
- After pressing the yellow tab, the battery should loosen.
- Slowly pull the battery completely out.
After pressing the yellow tab, the battery should loosen.
Slowly pull the battery completely out.
Step 5
Back Panel
- Using the T5 Torx screwdriver, remove all four 4mm screws.
Using the T5 Torx screwdriver, remove all four 4mm screws.
Step 6
- Using a Phillips #000 screwdriver, remove the single 3mm screw found inside the battery/charging compartment.
Using a Phillips #000 screwdriver, remove the single 3mm screw found inside the battery/charging compartment.
Step 7
- Remove the upper cover (connected by glue) and unscrew the single Philips screw.
Remove the upper cover (connected by glue) and unscrew the single Philips screw.
Step 8
- Remove two Philips screws from the bottom cover, lift gently the cover and remove the single Philips screw under it.
Remove two Philips screws from the bottom cover, lift gently the cover and remove the single Philips screw under it.
Step 9
- Carefully remove the back cover from the camera body.
Carefully remove the back cover from the camera body.
Step 10
LCD Screen
- Using a Phillips #000 screwdriver, remove all 11, 4mm screws on the LCD screen cover.
- Two screws are located on the right.
- The remaining screws are hidden behind a connector ribbon on the left.
Using a Phillips #000 screwdriver, remove all 11, 4mm screws on the LCD screen cover.
Two screws are located on the right.
The remaining screws are hidden behind a connector ribbon on the left.
Step 11
- Pull the LCD screen from the plastic frame after removing all of the screws.
Pull the LCD screen from the plastic frame after removing all of the screws.
Step 12
- Using a pair of tweezers from the precision tweezer set, carefully remove the screen from the metal frame.
- Since the tweezers could shatter the screen, causing for broken glass, exercise extreme caution.
Using a pair of tweezers from the precision tweezer set, carefully remove the screen from the metal frame.
Since the tweezers could shatter the screen, causing for broken glass, exercise extreme caution.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 1 other contributor
Lauren Stepp
Member since: 01/29/2016
1,251 Reputation
8 Guides authored
Badges:
15
+12 more badges
Team
Western Carolina University, Team 1-4, Virtue Spring 2016
Member of Western Carolina University, Team 1-4, Virtue Spring 2016
WCU-VIRTUE-S16S1G4
5 Members
16 Guides authored
Ben - Oct 25, 2016
Reply
Hi.
Where can you buy a replacement screen?
Jose Martins - Dec 24, 2016
Reply
my contact is josem6073@gmail.com
Thank you .
macreateur - Jan 28, 2017
Reply
Please add Torx T5 screwdriver at the tool needed, required at step 5
Costis Papaconstantinou - Aug 22, 2017
Reply
my contact is cpapacon@gmail.com
Keith Durkan - Apr 17, 2018
Reply
my contact is Keithdurkan@gmail.com