Difficulty
Moderate
Steps
14
Time Required
Suggest a time??
Sections
5
- Rear Panel
- 2 steps
- Battery
- 1 step
- SIM Card
- 1 step
- Rear Inner Frame
- 6 steps
- Motherboard
- 4 steps
Flags
1
Member-Contributed Guide
An awesome member of our community made this guide. It is not managed by iFixit staff.
BackSamsung Nexus S
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Rear Panel
- Gently insert a plastic opening tool between the rear panel and the inner rear frame near the rear-facing camera.
- Use your plastic opening tool to pry up the rear case around the perimeter of the Nexus S.
Gently insert a plastic opening tool between the rear panel and the inner rear frame near the rear-facing camera.
Use your plastic opening tool to pry up the rear case around the perimeter of the Nexus S.
1024
Step 2
- Remove the rear panel from the Nexus S.
Remove the rear panel from the Nexus S.
Step 3
Battery
- Using the edge of a plastic opening tool, lift the battery from the end closest to the headphone jack.
- Remove the battery from the Nexus S.
Using the edge of a plastic opening tool, lift the battery from the end closest to the headphone jack.
Remove the battery from the Nexus S.
Step 4
SIM Card
- Use your thumb to slide the SIM card downwards from the SIM card slot.
- Remove the SIM card.
Use your thumb to slide the SIM card downwards from the SIM card slot.
Remove the SIM card.
Step 5
Rear Inner Frame
- Remove the six Phillips screws securing the rear inner frame to the inner case.
Remove the six Phillips screws securing the rear inner frame to the inner case.
Step 6
- Insert the flat edge of a plastic opening tool in between the rear inner frame and the top left corner of the Nexus S.
- Pry the opening tool upwards to pop the top right corner from the clips securing it to the inner assembly.
Insert the flat edge of a plastic opening tool in between the rear inner frame and the top left corner of the Nexus S.
Pry the opening tool upwards to pop the top right corner from the clips securing it to the inner assembly.
Step 7
- Insert the plastic opening tool to the right of the power button.
- Slide the plastic opening tool downwards along the perimeter of the Nexus S to release the clips on the right side.
Insert the plastic opening tool to the right of the power button.
Slide the plastic opening tool downwards along the perimeter of the Nexus S to release the clips on the right side.
Step 8
- In the same manner as previously described, release the bottom clips located near the bottom of the Nexus S.
In the same manner as previously described, release the bottom clips located near the bottom of the Nexus S.
Step 9
- Insert and pry the plastic opening tool to release the final clip securing the rear inner frame to the inner assembly.
Insert and pry the plastic opening tool to release the final clip securing the rear inner frame to the inner assembly.
Step 10
- Lift and remove the rear inner frame from the Nexus S.
Lift and remove the rear inner frame from the Nexus S.
Step 11
Motherboard
- Disconnect the following cables from their respective sockets on the motherboard:
- Headphone jack cable
- Digitizer cable connector
- Camera/SIM board connector
Disconnect the following cables from their respective sockets on the motherboard:
Headphone jack cable
Digitizer cable connector
Camera/SIM board connector
Step 12
- Insert the flat edge of a plastic opening tool underneath the headphone jack connector and pry upwards.
- Make sure to pry on the connector and not the socket itself. Prying the socket may cause severe damage.
- Repeat the procedure for the digitizer and rear camera/SIM board connectors.
Insert the flat edge of a plastic opening tool underneath the headphone jack connector and pry upwards.
Make sure to pry on the connector and not the socket itself. Prying the socket may cause severe damage.
Repeat the procedure for the digitizer and rear camera/SIM board connectors.
Step 13
- Remove the three Phillips screws securing the motherboard to the front display assembly.
Remove the three Phillips screws securing the motherboard to the front display assembly.
Step 14
- Wedge the plastic opening tool near the bottom right corner of the motherboard and pry upwards to dislodge it from its recess.
- Lift and remove the motherboard.
Wedge the plastic opening tool near the bottom right corner of the motherboard and pry upwards to dislodge it from its recess.
Lift and remove the motherboard.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
15 other people completed this guide.
Author
with 2 other contributors
Walter Galan
682,038 Reputation
1,203 Guides authored
Badges:
54
+51 more badges