Difficulty
Moderate
Steps
14
Time Required
1 - 2 hours
Sections
2
- Battery
- 6 steps
- Headphone Jack
- 8 steps
Flags
1
Better Introduction
Improve this guide by completing or revising its introduction.
BackNexus 10
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Battery
- Using a plastic opening tool, remove the thin plastic cover from back of the tablet by prying up from its small tab.
Using a plastic opening tool, remove the thin plastic cover from back of the tablet by prying up from its small tab.
1024
Step 2
- Remove the five 2mm screws on the back of the device using a PH00 screwdriver.
Remove the five 2mm screws on the back of the device using a PH00 screwdriver.
Step 3
- Pry the device apart by inserting a plastic opening tool in the seam between the plastic backing and display assembly. Use the tool to unclip the plastic tabs in between the backing and the display.
- Pull the the plastic backing off the display assembly using your hands.
- Do not do this step with only your hands. You will require a significant amount of force to separate the device.
Pry the device apart by inserting a plastic opening tool in the seam between the plastic backing and display assembly. Use the tool to unclip the plastic tabs in between the backing and the display.
Pull the the plastic backing off the display assembly using your hands.
Do not do this step with only your hands. You will require a significant amount of force to separate the device.
Step 4
- Detach the three connector ribbons passing over the battery using the plastic opening tool.
Detach the three connector ribbons passing over the battery using the plastic opening tool.
Step 5
- Remove the twelve 2mm screws around the perimeter of the battery with a PH00 screwdriver.
Remove the twelve 2mm screws around the perimeter of the battery with a PH00 screwdriver.
Step 6
- Disconnect the battery by lifting it upward and pulling it away from the connector.
Disconnect the battery by lifting it upward and pulling it away from the connector.
Step 7
Headphone Jack
- Remove one screw on the logic board with a PH00 screwdriver.
Remove one screw on the logic board with a PH00 screwdriver.
Step 8
- Disconnect right speaker connector ribbon from logic board.
- Lift the speaker out by pulling up on its corner.
Disconnect right speaker connector ribbon from logic board.
Lift the speaker out by pulling up on its corner.
Step 9
- Disconnect connectors around the perimeter of the motherboard.
Disconnect connectors around the perimeter of the motherboard.
Step 10
- Remove motherboard by gently pulling upward under its corner.
Remove motherboard by gently pulling upward under its corner.
Step 11
- Remove the three 2mm screws along the right side of the device using a PH00 screwdriver.
Remove the three 2mm screws along the right side of the device using a PH00 screwdriver.
Step 12
- Unseat the small vibrator motor by gently applying upward pressure with a spudger.
Unseat the small vibrator motor by gently applying upward pressure with a spudger.
Step 13
- Lift the assembly by gently applying upward pressure with the spudger on the assembly.
Lift the assembly by gently applying upward pressure with the spudger on the assembly.
Step 14
- Gently pull battery-audio jack-USB assembly upward, detaching it from its adhesive.
Gently pull battery-audio jack-USB assembly upward, detaching it from its adhesive.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
5 other people completed this guide.
Author
with 4 other contributors
Benjamin Troller
Member since: 04/11/2016
2,139 Reputation
5 Guides authored
Badges:
13
+10 more badges
Team
Cal Poly, Team 34-18, Maness Spring 2016
Member of Cal Poly, Team 34-18, Maness Spring 2016
CPSU-MANESS-S16S34G18
4 Members
5 Guides authored
Mauri - Feb 10, 2017
Reply
Perfect guide, I managed to fix my Nexus 10 broken usb port.
It may be worth to mention after step 14 you need to gently remove the plastic connectors cover and place it on the replacement part.