Nextbook Nxa8Qc116B Display Assembly Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          30 minutes

Sections

Battery
16 steps
Motherboard
13 steps
Display Assembly
2 steps

Flags

BackNextbook NXA8QC116B
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

If you see any leakage coming from the tablet do not open the back cover!
Ensure you do not pry around the buttons. This could result in damage and render them inoperable.
With the tip of the thin metal spudger in place, use a prying motion to work the spudger down the side to the corner of the device.

If you see any leakage coming from the tablet do not open the back cover!

Ensure you do not pry around the buttons. This could result in damage and render them inoperable.

With the tip of the thin metal spudger in place, use a prying motion to work the spudger down the side to the corner of the device.

1024

Step 2

Continue working the spudger downward and pry with the spudger until the bottom left-hand corner of the tablet is reached.

Continue working the spudger downward and pry with the spudger until the bottom left-hand corner of the tablet is reached.

Step 3

Along the bottom of the tablet, keep using a working and prying motion with the spudger to loosen the cover.

Along the bottom of the tablet, keep using a working and prying motion with the spudger to loosen the cover.

Step 4

Continue prying motion until the bottom right-hand corner of the tablet is reached.

Continue prying motion until the bottom right-hand corner of the tablet is reached.

Step 5

Work the spudger to the upper left-hand corner of the tablet.

Work the spudger to the upper left-hand corner of the tablet.

Step 6

Be careful once you get to the top of the tablet with the spudger so as not to damage the headphone jack and other ports.
When prying along the top of the tablet, try to keep the spudger between 70 to 85 degrees (almost perpendicular) to the tablet screen.
Continue working the spudger around the tablet until the cover of the device comes off

Be careful once you get to the top of the tablet with the spudger so as not to damage the headphone jack and other ports.

When prying along the top of the tablet, try to keep the spudger between 70 to 85 degrees (almost perpendicular) to the tablet screen.

Continue working the spudger around the tablet until the cover of the device comes off

Step 7

Separate from the cover from the tablet.

Separate from the cover from the tablet.

Step 8

Locate and carefully remove the yellow cellophane tape from the red and black speaker wires that connect the speaker to the edge of the motherboard.

Locate and carefully remove the yellow cellophane tape from the red and black speaker wires that connect the speaker to the edge of the motherboard.

Step 9

Locate and carefully remove the yellow cellophane tape with tweezers from the battery connector and black and red speaker wires on the edge of the motherboard.

Locate and carefully remove the yellow cellophane tape with tweezers from the battery connector and black and red speaker wires on the edge of the motherboard.

Step 10

Using small pliers, carefully disconnect the male battery connector from the motherboard.
If you are only replacing the front camera, skip to step 17 in the camera replacement guide and continue.

Using small pliers, carefully disconnect the male battery connector from the motherboard.

If you are only replacing the front camera, skip to step 17 in the camera replacement guide and continue.

Step 11

If the battery is leaking or bulging, stop and get away from it!
Carefully remove the gray square pad glued to both the white ribbon cable and the battery by pulling slowly.

If the battery is leaking or bulging, stop and get away from it!

Carefully remove the gray square pad glued to both the white ribbon cable and the battery by pulling slowly.

Step 12

Locate the white ribbon cable Zero Insertion Force (ZIF) connector between the battery and the motherboard, and peel the yellow cellophane tape off the connector.

Locate the white ribbon cable Zero Insertion Force (ZIF) connector between the battery and the motherboard, and peel the yellow cellophane tape off the connector.

Step 13

Flip up the gray retainer clip on the white ribbon cable ZIF connector on the motherboard with your fingernail. If you do not have fingernails long enough, carefully use a black plastic spudger.

Flip up the gray retainer clip on the white ribbon cable ZIF connector on the motherboard with your fingernail. If you do not have fingernails long enough, carefully use a black plastic spudger.

Step 14

Remove the white ribbon cable and carefully peel it off the battery.

Remove the white ribbon cable and carefully peel it off the battery.

Step 15

Move the spudger in a left-to-right scraping motion to loosen the glue until the battery is separated from the tablet.

Move the spudger in a left-to-right scraping motion to loosen the glue until the battery is separated from the tablet.

Step 16

Remove the battery.

Remove the battery.

Step 17

              Motherboard

Locate and remove the yellow cellophane tape from the display assembly ribbon cable ZIF connector.

Locate and remove the yellow cellophane tape from the display assembly ribbon cable ZIF connector.

Step 18

Locate the volume, power, home button ribbon cable ZIF connector.

Locate the volume, power, home button ribbon cable ZIF connector.

Step 19

Flip the ZIF connector retainer up with your fingernail. If you do not have fingernails long enough, carefully use the black plastic spudger.

Flip the ZIF connector retainer up with your fingernail. If you do not have fingernails long enough, carefully use the black plastic spudger.

Step 20

Remove the ribbon cable by gently pulling on it.

Remove the ribbon cable by gently pulling on it.

Step 21

Locate the Display Assembly ribbon cable ZIF connector, and using tweezers, remove the yellow cellophane tape.

Locate the Display Assembly ribbon cable ZIF connector, and using tweezers, remove the yellow cellophane tape.

Step 22

Put your fingernail under the gray ZIF connector retainer and flip the retainer up. If you do not have fingernails long enough, carefully use a black plastic spudger.

Put your fingernail under the gray ZIF connector retainer and flip the retainer up. If you do not have fingernails long enough, carefully use a black plastic spudger.

Step 23

Remove the Display Assembly ribbon cable by gently pulling on it.

Remove the Display Assembly ribbon cable by gently pulling on it.

Step 24

Use small pliers to pull the connector, wiggling it a little as you pull it from its connection.

Use small pliers to pull the connector, wiggling it a little as you pull it from its connection.

Step 25

Using a J00 screwdriver, remove the 4 black 4.0 mm screws.
There is no screw at this location.

Using a J00 screwdriver, remove the 4 black 4.0 mm screws.

There is no screw at this location.

Step 26

Locate the ZIF connector to remove the white ribbon cable

Locate the ZIF connector to remove the white ribbon cable

Step 27

To remove the white ribbon cable, put your fingernail under the gray ZIF connector retainer and flip the retainer up.

To remove the white ribbon cable, put your fingernail under the gray ZIF connector retainer and flip the retainer up.

Step 28

Ensure the ribbon cable does not get caught when removing the motherboard. Damage to the ribbon cable may result.
Pull the motherboard back over the copper tape to tear the tape and remove the motherboard.

Ensure the ribbon cable does not get caught when removing the motherboard. Damage to the ribbon cable may result.

Pull the motherboard back over the copper tape to tear the tape and remove the motherboard.

Step 29

Remove the remaining copper tape from the back of the display assembly and the motherboard.
Replace with new tape when reassembling.

Remove the remaining copper tape from the back of the display assembly and the motherboard.

Replace with new tape when reassembling.

Step 30

              Display Assembly

Locate and remove the 3 black 4.0 mm screws on the speaker panel using a J00 screwdriver.
Disconnect the speaker from the motherboard.
Remove the panel.

Locate and remove the 3 black 4.0 mm screws on the speaker panel using a J00 screwdriver.

Disconnect the speaker from the motherboard.

Remove the panel.

Step 31

Display Assembly

Display Assembly

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 4 other contributors

                    Robert Englehardt

Member since: 09/27/2017

682 Reputation

                                      5 Guides authored                  



                       Badges:
                       13







                                                        +10 more badges

Team

                       Eastern Washington University, Team S1-G7, Carnegie Fall 2017                        

                                                  Member of Eastern Washington University, Team S1-G7, Carnegie Fall 2017 



                    EWU-CARNEGIE-F17S1G7                     


                                            4 Members                     


                                            5 Guides authored

Susann - May 10, 2018

Would these instructions be the same for a Nextbook ares11a?

Rosalina Reyes - Feb 6, 2020

I would think so, it’s basically the same adaptation for all laptops.

Introduction#

What you need#

Team#

Introduction

What you need

Team