Difficulty
Difficult
Steps
10
Time Required
20 - 25 minutes
Sections
2
- Back Panel
- 5 steps
- Battery
- 5 steps
Flags
0
BackNextbook NX008HD8G
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Panel
- Using your finger, open the plastic tab to the right of the rear-facing camera.
- Wedge your fingernail in between the back panel and the plastic tab and pull the plastic tab towards your body.
Using your finger, open the plastic tab to the right of the rear-facing camera.
Wedge your fingernail in between the back panel and the plastic tab and pull the plastic tab towards your body.
1024
Step 2
- Using your finger, remove the SD card by pressing down on top of it (toward the bottom of the device) until you hear a clicking sound.
- Once the card pops out, use your finger to pull the card completely out of the SD card slot.
Using your finger, remove the SD card by pressing down on top of it (toward the bottom of the device) until you hear a clicking sound.
Once the card pops out, use your finger to pull the card completely out of the SD card slot.
Step 3
- Remove the 5 mm screw using the Phillips PH00 bit in the iFixit metal Screwdriver.
Remove the 5 mm screw using the Phillips PH00 bit in the iFixit metal Screwdriver.
Step 4
- Use the plastic opening tool to separate the back panel by carefully sliding the narrow end of the tool between the front glass and back panel.
- Use a second plastic opening tool to help pry the front glass from the back panel.
- You will hear some cracking sounds when separating the front glass from the back panel. That is okay! That is the back panel latches releasing the front glass.
Use the plastic opening tool to separate the back panel by carefully sliding the narrow end of the tool between the front glass and back panel.
Use a second plastic opening tool to help pry the front glass from the back panel.
You will hear some cracking sounds when separating the front glass from the back panel. That is okay! That is the back panel latches releasing the front glass.
Step 5
- Use your hands to completely separate the rest of the front glass from the back panel.
- Do not to pull the device apart with too much force. If you do, you may break or bend the back panel.
Use your hands to completely separate the rest of the front glass from the back panel.
Do not to pull the device apart with too much force. If you do, you may break or bend the back panel.
Step 6
Battery
- Remove yellow tape with a black edge that covers the red, white and black wires.
- The yellow tape with a black edge is safe to remove completely.
Remove yellow tape with a black edge that covers the red, white and black wires.
The yellow tape with a black edge is safe to remove completely.
Step 7
- Remove the white masking tape covering the red white and black wires.
Remove the white masking tape covering the red white and black wires.
Step 8
- Desolder the red, white and black wires on the left side of the motherboard.
Desolder the red, white and black wires on the left side of the motherboard.
Step 9
- Use the flat end of the spudger to carefully separate the smaller, silver battery square from the digitizer.
- The battery is very malleable, do not try to take it all off at once.
Use the flat end of the spudger to carefully separate the smaller, silver battery square from the digitizer.
The battery is very malleable, do not try to take it all off at once.
Step 10
- Use the flat end of the spudger to carefully separate the large battery from the digitizer.
- The battery is very malleable, do not try to take it all off at once.
Use the flat end of the spudger to carefully separate the large battery from the digitizer.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 2 other contributors
Philip Gai
Member since: 09/22/2015
759 Reputation
3 Guides authored
Badges:
17
+14 more badges
Team
Baylor, Team 10-15, Williams Fall 2015
Member of Baylor, Team 10-15, Williams Fall 2015
BU-WILLIAMS-F15S10G15
3 Members
8 Guides authored
intessol - Oct 28, 2016
Reply
Clear & concise. Nice job! Even I could follow it!! ;-)
ken fukushima - Apr 21, 2017
Reply
Excellent guide, easy to follow, very concise, very good photographs. Thank you
Lauraelena - Nov 12, 2020
Reply
Donde puedo encontrar una batería