Featured
Featured Guide
Difficulty
Moderate
Steps
11
Time Required
15 minutes
Sections
3
- Lower Case
- 4 steps
- Motherboard
- 2 steps
- Antenna
- 5 steps
Flags
1
Featured Guide
This guide has been found to be exceptionally cool by the iFixit staff.
BackNetgear WGR614v9
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Lower Case
- Rotate the device so that the bottom is facing up.
Rotate the device so that the bottom is facing up.
1024
Step 2
- Lift up all four rubber pads on the bottom of the router with the plastic opening tool.
- Be careful not to pull the rubber pads all the way out when lifting as they are difficult to reinsert.
Lift up all four rubber pads on the bottom of the router with the plastic opening tool.
Be careful not to pull the rubber pads all the way out when lifting as they are difficult to reinsert.
Step 3
- Unscrew the four 11.8 mm T-8 torx screws from the bottom of the router.
Unscrew the four 11.8 mm T-8 torx screws from the bottom of the router.
Step 4
- Lift the bottom casing straight up from the router.
Lift the bottom casing straight up from the router.
Step 5
Motherboard
- Remove the clear plastic casing by lifting it straight up from the router.
Remove the clear plastic casing by lifting it straight up from the router.
Step 6
- Separate the motherboard from the top shell by lifting it straight up from the router.
Separate the motherboard from the top shell by lifting it straight up from the router.
Step 7
Antenna
- Rotate the motherboard so that the top is facing up.
- Set the motherboard on a flat clean surface.
Rotate the motherboard so that the top is facing up.
Set the motherboard on a flat clean surface.
Step 8
- Do not refer to the pictures in this step for proper de-soldering and soldering techniques. They are for illustration purposes only.
- Refer to this link for proper de-soldering and soldering techniques.
- Be patient. This may take some time depending on the quality of your soldering iron.
Do not refer to the pictures in this step for proper de-soldering and soldering techniques. They are for illustration purposes only.
Refer to this link for proper de-soldering and soldering techniques.
Be patient. This may take some time depending on the quality of your soldering iron.
Step 9
- Peel off the yellow tape holding the wires.
- Set the tape aside on a clean surface so that it can be reused.
Peel off the yellow tape holding the wires.
Set the tape aside on a clean surface so that it can be reused.
Step 10
- Extend the antenna outwards from the device so that it is straight.
- Locate the clips that hold the antenna onto the router.
- Push the clips in with one hand and pull the antenna out with your other hand. Slightly twist the antenna until it becomes free from the hole.
Extend the antenna outwards from the device so that it is straight.
Locate the clips that hold the antenna onto the router.
Push the clips in with one hand and pull the antenna out with your other hand. Slightly twist the antenna until it becomes free from the hole.
Step 11
- Pull out the antenna as well as the connected wire.
Pull out the antenna as well as the connected wire.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 7 other contributors
Ryan Murphy
Member since: 10/03/2011
488 Reputation
4 Guides authored
Badges:
10
+7 more badges
Team
Cal Poly, Team 21-24, Maness Fall 2011
Member of Cal Poly, Team 21-24, Maness Fall 2011
CPSU-MANESS-F11S21G24
4 Members
6 Guides authored