Difficulty

Easy

Steps

8

Time Required

                          5 minutes

Sections

2

  • Battery
  • 3 steps
  • Plastic Housing
  • 5 steps

Flags

0

  • BackNetgear Arlo

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Locate unlock switch on underside of camera and unlock it by sliding it.
  • Once unlocked, slide the cover out and up to open the battery housing.

Locate unlock switch on underside of camera and unlock it by sliding it.

Once unlocked, slide the cover out and up to open the battery housing.

1024

Step 2

  • Remove all 4 of the 3.0 Volt batteries from the battery housing.

Remove all 4 of the 3.0 Volt batteries from the battery housing.

Step 3

  • Inspect prongs at the bottom of the battery housing to ensure that they are not bent or broken before replacing the batteries.

Inspect prongs at the bottom of the battery housing to ensure that they are not bent or broken before replacing the batteries.

Step 4

              Plastic Housing
  • Remove the 2 (3.5mm) housing screws with a J0 screwdriver.

Remove the 2 (3.5mm) housing screws with a J0 screwdriver.

Step 5

  • Slide the unlocked battery cover forward to remove 2 (3.5mm) screws, that are behind the cover.

Slide the unlocked battery cover forward to remove 2 (3.5mm) screws, that are behind the cover.

Step 6

  • Open the battery cover and remove the 2 (3.5mm") screws from under the cover.

Open the battery cover and remove the 2 (3.5mm") screws from under the cover.

Step 7

  • Use a plastic opening tool to start separating the plastic housing from the front side of the battery cover.
  • Next, start separating the plastic cover from the rear of the plastic housing, and work your way down the seam line.
  • Make sure the plastics snaps on the front of the plastic get unhooked from the grey plastic ring around the front of the camera.

Use a plastic opening tool to start separating the plastic housing from the front side of the battery cover.

Next, start separating the plastic cover from the rear of the plastic housing, and work your way down the seam line.

Make sure the plastics snaps on the front of the plastic get unhooked from the grey plastic ring around the front of the camera.

Step 8

  • Remove the screw (3.5mm) near the sync button holding the opposite side of the camera on.
  • Remove the second screw (3.5mm) on the back of the camera to remove the second housing.
  • Once the screws are removed use an opening tool to pry back the second plastic mount.

Remove the screw (3.5mm) near the sync button holding the opposite side of the camera on.

Remove the second screw (3.5mm) on the back of the camera to remove the second housing.

Once the screws are removed use an opening tool to pry back the second plastic mount.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Connor Krampen

Member since: 01/08/2018

375 Reputation

                                      3 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       IUPUI, Team S1-G1, Freund Spring 2018                        

                                                  Member of IUPUI, Team S1-G1, Freund Spring 2018 



                    IUPUI-FREUND-S18S1G1                     


                                            2 Members                     


                                            6 Guides authored

L R Hardy - Jun 13, 2018

Reply

Where can I buy replacement parts like a battery cover for Arlo