Netgear Arlo Charging Port Replacement Repair Guide

Difficulty

Moderate

Steps

14

Time Required

                          8 minutes            

Sections

3

• Plastic Housing
• 5 steps
• Lens Assembly
• 4 steps
• Charging Port
• 5 steps

Flags

0

• BackNetgear Arlo

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Plastic Housing               

• Remove the 2 (3.5mm) housing screws with a J0 screwdriver.

Remove the 2 (3.5mm) housing screws with a J0 screwdriver.

1024

Step 2

• Slide the unlocked battery cover forward to remove 2 (3.5mm) screws, that are behind the cover.

Slide the unlocked battery cover forward to remove 2 (3.5mm) screws, that are behind the cover.

Step 3

• Open the battery cover and remove the 2 (3.5mm") screws from under the cover.

Open the battery cover and remove the 2 (3.5mm") screws from under the cover.

Step 4

• Use a plastic opening tool to start separating the plastic housing from the front side of the battery cover.
• Next, start separating the plastic cover from the rear of the plastic housing, and work your way down the seam line.
• Make sure the plastics snaps on the front of the plastic get unhooked from the grey plastic ring around the front of the camera.

Use a plastic opening tool to start separating the plastic housing from the front side of the battery cover.

Next, start separating the plastic cover from the rear of the plastic housing, and work your way down the seam line.

Make sure the plastics snaps on the front of the plastic get unhooked from the grey plastic ring around the front of the camera.

Step 5

• Remove the screw (3.5mm) near the sync button holding the opposite side of the camera on.
• Remove the second screw (3.5mm) on the back of the camera to remove the second housing.
• Once the screws are removed use an opening tool to pry back the second plastic mount.

Remove the screw (3.5mm) near the sync button holding the opposite side of the camera on.

Remove the second screw (3.5mm) on the back of the camera to remove the second housing.

Once the screws are removed use an opening tool to pry back the second plastic mount.

Step 6

              Lens Assembly               

• Remove 4 (6mm) large screws with a J00 screwdriver.
• There are 2 on each side. This will allow you to remove the clear housing from the white housing.

Remove 4 (6mm) large screws with a J00 screwdriver.

There are 2 on each side. This will allow you to remove the clear housing from the white housing.

Step 7

• Once screws are removed, pull apart the clear housing.
• Remove rod from camera cover.

Once screws are removed, pull apart the clear housing.

Remove rod from camera cover.

Step 8

• Remove Large ribbon cable first to disconnect front of camera from main body.
• Remove 4 (3.5mm) small black screws from motherboard of the camera unit.
• Remove smaller ribbon cable from underneath yellow tape.

Remove Large ribbon cable first to disconnect front of camera from main body.

Remove 4 (3.5mm) small black screws from motherboard of the camera unit.

Remove smaller ribbon cable from underneath yellow tape.

Step 9

• Once all ribbon cables are removed, remove the motherboard and camera assembly by pulling up on the black camera motherboard.

Once all ribbon cables are removed, remove the motherboard and camera assembly by pulling up on the black camera motherboard.

Step 10

              Charging Port               

• Remove the 2 (.135") housing screws with a JIS00 screwdriver

Remove the 2 (.135") housing screws with a JIS00 screwdriver

Step 11

• Remove 4 (.135") screws on the inside of the battery compartment using the JIS 00 screwdriver.

Remove 4 (.135") screws on the inside of the battery compartment using the JIS 00 screwdriver.

Step 12

• Slide the two halves apart

Slide the two halves apart

Step 13

• Remove the 2 (.135") screws holding the charging port on using the JIS 00 screwdriver.

Remove the 2 (.135") screws holding the charging port on using the JIS 00 screwdriver.

Step 14

• Remove the ribbon by prying the black ribbon holder up using the opening tool.
• Pull the ribbon away from the charging port.

Remove the ribbon by prying the black ribbon holder up using the opening tool.

Pull the ribbon away from the charging port.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.                                             

Author

                                      with 1 other contributor 

                    Brian Johnson                     

Member since: 03/21/2018

184 Reputation

                                      1 Guide authored                  



                       Badges:
                       5







                                                        +2 more badges                           

Team

                       IUPUI, Team S2-G1, Freund Spring 2018                        

                                                  Member of IUPUI, Team S2-G1, Freund Spring 2018 



                    IUPUI-FREUND-S18S2G1                     


                                            2 Members                     


                                            4 Guides authored                     

Bob Olive Sr - Aug 27, 2018

Reply

Great Job, Thank you!

mikewalters1951 - Oct 18, 2019

Reply

Great thanks where did you get the replacement cable please thanks Mike

robertwatkins61 - Nov 26, 2019

Reply

where did you get the replacement cable please thanks  BOB