Nest Outdoor Camera Usb Cable Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          30 minutes - 1 hour

Sections

USB Cable
13 steps

Flags

Bullets!

Better coordination with markups and the color/type of bullets will help make this guide more clear!

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Needs More Images

A few more images would make this guide’s procedures crystal clear.

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

BackNest Outdoor Camera
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

What you need

Step 1

              USB Power Cable Corroded

The Nest Outdoor Camera (not to be confused with the Nest IQ Outdoor Camera) gets power through a long USB cable that connects to a power adapter, which connects to an outlet. The USB connector is not as waterproof as advertised, and this one got wet, became corroded, and the camera stopped working.

The Nest Outdoor Camera (not to be confused with the Nest IQ Outdoor Camera) gets power through a long USB cable that connects to a power adapter, which connects to an outlet. The USB connector is not as waterproof as advertised, and this one got wet, became corroded, and the camera stopped working.

1024

Step 2

              Evaluate the condition of both power cables

Take a close look at the USB power adapter (which runs from the outlet to the USB hub) and the USB cable (which runs from the USB cable to the camera). Are they both corroded?
Google/Nest no longer supports or makes this product, so replacement power adapters are hard to find. Fortunately, this power adapter is functionally a phone charger cube, which converts wall power to 5V 1.4A USB power. It can be replaced by any comparable charging adapter that outputs 5V and 1.4+Amps in a female USB A port.

Take a close look at the USB power adapter (which runs from the outlet to the USB hub) and the USB cable (which runs from the USB cable to the camera). Are they both corroded?

Google/Nest no longer supports or makes this product, so replacement power adapters are hard to find. Fortunately, this power adapter is functionally a phone charger cube, which converts wall power to 5V 1.4A USB power. It can be replaced by any comparable charging adapter that outputs 5V and 1.4+Amps in a female USB A port.

Step 3

              Determine cable length

If you’re removing the power adapter from the setup, your required cable length may change. Measure how far you need the power cable to run. When I did this, I added an outdoor USB outlet near where the camera would (re)mount, so I chose to make the cable significantly shorter.
Measure the camera USB cable (from the camera, not the USB) to your desired length. Give yourself a few extra inches in chase you cut the wires while striping.

If you’re removing the power adapter from the setup, your required cable length may change. Measure how far you need the power cable to run. When I did this, I added an outdoor USB outlet near where the camera would (re)mount, so I chose to make the cable significantly shorter.

Measure the camera USB cable (from the camera, not the USB) to your desired length. Give yourself a few extra inches in chase you cut the wires while striping.

Step 4

              Cut and Strip the camera cable

Cut the camera cable at the desired length using wire cutters.
Carefully begin stripping the white sheathing. I found that a careful incision with an Xacto knife along the length of the sheathing helpful to get started. Use scissors or wire cutters to remove excess insulation once pulled off the wires.
I stripped the wire ~2 inches (which is longer than shown in this photo).
You should see a red wire, a black wire, and two other wires bundled in an additional sheath. There may also be loose wire mesh around the wires, which you can pull away and cut off.

Cut the camera cable at the desired length using wire cutters.

Carefully begin stripping the white sheathing. I found that a careful incision with an Xacto knife along the length of the sheathing helpful to get started. Use scissors or wire cutters to remove excess insulation once pulled off the wires.

I stripped the wire ~2 inches (which is longer than shown in this photo).

You should see a red wire, a black wire, and two other wires bundled in an additional sheath. There may also be loose wire mesh around the wires, which you can pull away and cut off.

Step 5

              Cut the new USB cable

Figure out what length of new USB cable you want and cut it to that length. Leave a few extra inches in case you cut the wires while striping

Figure out what length of new USB cable you want and cut it to that length. Leave a few extra inches in case you cut the wires while striping

Step 6

              Strip the USB cable

Carefully strip 1-2in of the outer plastic from the USB cable. You’ll likely see some wire mesh and/or foil. Peel those away.

Carefully strip 1-2in of the outer plastic from the USB cable. You’ll likely see some wire mesh and/or foil. Peel those away.

Step 7

              Strip the Red Wires

Sorry - I stopped taking photos at this point.
Carefully strip ~1inch off the red wire on the camera and the USB cable. They will probably be stranded core (made of lots of smaller wires). Twist each wire to make the stranded core more solid.

Sorry - I stopped taking photos at this point.

Carefully strip ~1inch off the red wire on the camera and the USB cable. They will probably be stranded core (made of lots of smaller wires). Twist each wire to make the stranded core more solid.

Step 8

              Add heat shrink tubing

It’s very easy to forget this step when splicing. Slide several heat shrink wrap tubes over the prepped wires. You’ll want a small one on the red wire and black wire and several much larger ones on the camera cable for putting it all together later.
Heat shrink wrap tubing is cheap - you’re better off having an extra tube on the wire that you don’t need (and can carefully cut off later) than being one short and having exposed wires.

It’s very easy to forget this step when splicing. Slide several heat shrink wrap tubes over the prepped wires. You’ll want a small one on the red wire and black wire and several much larger ones on the camera cable for putting it all together later.

Heat shrink wrap tubing is cheap - you’re better off having an extra tube on the wire that you don’t need (and can carefully cut off later) than being one short and having exposed wires.

Step 9

              Splice the Red Wires

There are lots of good tutorials online on soldering and splicing wires.
Using your favorite method, splice the red wires together. Solder them well.

There are lots of good tutorials online on soldering and splicing wires.

Using your favorite method, splice the red wires together. Solder them well.

Step 10

              Heat Shrink the red wires

Slide your heat shrink tubing from further down the red wires until it covers the spliced connection. Use a heat gun to shrink the tubing into place.
Be careful not to shrink the tubing around the black wires or the camera cable.

Slide your heat shrink tubing from further down the red wires until it covers the spliced connection. Use a heat gun to shrink the tubing into place.

Be careful not to shrink the tubing around the black wires or the camera cable.

Step 11

              Splice and heat shrink the black wires

Same exact steps here with the black wires. It doesn’t matter which color wire you do first - I have them listed as separate steps to limit potential mixups.
There will likely be other wires in both USB cables. They’re not needed for power and can be ignored.

Same exact steps here with the black wires. It doesn’t matter which color wire you do first - I have them listed as separate steps to limit potential mixups.

There will likely be other wires in both USB cables. They’re not needed for power and can be ignored.

Step 12

              Heat shrink tube both wires

Now you’re done with soldering.
Slide your heat shrink tubes from the camera cable down to the red and black spliced wires. Use the heat gun to shrink the tubes into place. You may need multiple tubes.

Now you’re done with soldering.

Slide your heat shrink tubes from the camera cable down to the red and black spliced wires. Use the heat gun to shrink the tubes into place. You may need multiple tubes.

Step 13

              Plug in the camera

If all went well, you’re now done!
Plug the camera into it’s power adapter (or a comparable USB power supply). If the blue light turns on, it works!

If all went well, you’re now done!

Plug the camera into it’s power adapter (or a comparable USB power supply). If the blue light turns on, it works!

Great work! Plug the new USB cable into the power adapter (or a comparable USB power supply) and wait a moment for the camera to turn on. If it works, you’ll see a blue light and then a green light. Use the Nest app to setup the camera, if necessary.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors

                    Brian Bock

Member since: 01/28/2018

252 Reputation

                                      1 Guide authored                  



                       Badges:
                       4







                                                        +1 more badge

Bullets!#

Needs Better Images#

Needs More Images#

Member-Contributed Guide#

What you need#

Bullets!

Needs Better Images

Needs More Images

Member-Contributed Guide

What you need