Difficulty

Moderate

Steps

10

Time Required

                          5 - 10 minutes

Sections

2

  • Battery
  • 7 steps
  • Auto-Away Sensor
  • 3 steps

Flags

0

  • BackNest Learning Thermostat 2nd Generation

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Removal from Wall
  • Grasp the display’s metal outer ring with your fingers and pull directly away from the wall.

Grasp the display’s metal outer ring with your fingers and pull directly away from the wall.

1024

Step 2

              Open Display
  • Turn the display over.
  • Remove the four 6 mm screws from the back of the display using a Phillips #0 screwdriver.

Turn the display over.

Remove the four 6 mm screws from the back of the display using a Phillips #0 screwdriver.

Step 3

              Remove the back of the display
  • Pinch the gray 20-pin connector with your fingers and pull directly away from the display.
  • Do NOT pull too far as there is a ribbon on the back panel connecting the 20-pin connector to the display.

Pinch the gray 20-pin connector with your fingers and pull directly away from the display.

Do NOT pull too far as there is a ribbon on the back panel connecting the 20-pin connector to the display.

Step 4

              Disconnect the base connection ribbon cable.
  • Locate the blue pull tab at the end of the ribbon which says, “1. Pull”.
  • Grasp the tab with your fingers and pull directly away from the motherboard.

Locate the blue pull tab at the end of the ribbon which says, “1. Pull”.

Grasp the tab with your fingers and pull directly away from the motherboard.

Step 5

              Lift battery from the base
  • Locate the blue tab which says, “2. Pull”.
  • Use tweezers to pull the battery up and away from the display.
  • Do NOT pull too far, as the battery is still connected to the motherboard and must be unplugged.

Locate the blue tab which says, “2. Pull”.

Use tweezers to pull the battery up and away from the display.

Do NOT pull too far, as the battery is still connected to the motherboard and must be unplugged.

Step 6

              Disconnect the battery from the motherboard
  • Locate the blue tab which says “3 unplug”.
  • Grasp the battery with your fingers. Pull gently directly away from the display to unplug the battery from the motherboard.

Locate the blue tab which says “3 unplug”.

Grasp the battery with your fingers. Pull gently directly away from the display to unplug the battery from the motherboard.

Step 7

              Remove battery from the display
  • Grasp the battery with your fingers and pull directly away from motherboard to separate the battery from the display.

Grasp the battery with your fingers and pull directly away from motherboard to separate the battery from the display.

Step 8

              Locate auto-away sensor
  • Locate the auto-away sensor.

Locate the auto-away sensor.

Step 9

              Remove screws
  • Remove the four 3mm screws with a #0 Phillips screwdriver.
  • Remove the one 4mm screw located at the edge of the auto-away sensor. Use a #0 Phillips screwdriver.

Remove the four 3mm screws with a #0 Phillips screwdriver.

Remove the one 4mm screw located at the edge of the auto-away sensor. Use a #0 Phillips screwdriver.

Step 10

              Remove auto-away sensor
  • Lift the auto-away sensor from motherboard using tweezers.
  • Peel the copper foil gently from the EMI shield.

Lift the auto-away sensor from motherboard using tweezers.

Peel the copper foil gently from the EMI shield.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 4 other contributors 


                    Justin Curry

Member since: 09/23/2014

258 Reputation

                                      2 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       USF Tampa, Team 11-5, Blackwell Fall 2014                        

                                                  Member of USF Tampa, Team 11-5, Blackwell Fall 2014 



                    USFT-BLACKWELL-F14S11G5                     


                                            5 Members                     


                                            11 Guides authored