Difficulty

Moderate

Steps

16

Time Required

Suggest a time??

Sections

2

  • Dismantle Nespresso CitiZ
  • 9 steps
  • Brewing unit
  • 7 steps

Flags

1

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackNespresso CitiZ

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Dismantle Nespresso CitiZ
  • Never forget: pull the plug!
  • Remove all attachments: Water tank, capsule and cup drawer, drip tray.
  • The model shown is also equipped with a milk frother, remove that too.

Never forget: pull the plug!

Remove all attachments: Water tank, capsule and cup drawer, drip tray.

The model shown is also equipped with a milk frother, remove that too.

1024

Step 2

  • The bottom is secured by oval head screws.
  • These screws have an oval head that makes them look like rivets (picture 2). You need to use a special bit - also available at iFixit - for their removal. Here a DIY guide. If the right bit is not available, it could be done with a pair of needle nose pliers. Nespresso wants to keep us out of our own machines!!!
  • Remove five oval head screws securing the large bottom panel.
  • Note: this panel is smaller on models without milk frother.

The bottom is secured by oval head screws.

These screws have an oval head that makes them look like rivets (picture 2). You need to use a special bit - also available at iFixit - for their removal. Here a DIY guide. If the right bit is not available, it could be done with a pair of needle nose pliers. Nespresso wants to keep us out of our own machines!!!

Remove five oval head screws securing the large bottom panel.

Note: this panel is smaller on models without milk frother.

Step 3

  • The bottom panel is just snapped into place. Insert a metal spudger into the slots and lift the panel out. It sits quite tightly and you might use some force to get it out.

The bottom panel is just snapped into place. Insert a metal spudger into the slots and lift the panel out. It sits quite tightly and you might use some force to get it out.

Step 4

  • Remove the large bottom panel.

Remove the large bottom panel.

Step 5

  • Use a spudger to slide off the two silicon tubes.

Use a spudger to slide off the two silicon tubes.

Step 6

  • Disconnect the two spade plugs on the blue and brown wires from the power switch. The two left ones remain.

Disconnect the two spade plugs on the blue and brown wires from the power switch. The two left ones remain.

Step 7

  • Remove four oval head screws from the small bottom panel.
  • Remove the main device from the base. It´s still connected with some wires, but this doesn´t bother much.

Remove four oval head screws from the small bottom panel.

Remove the main device from the base. It´s still connected with some wires, but this doesn´t bother much.

Step 8

  • The two colored side panels are only snapped into place. However, the latches sit very tight. You really need a lot of force. First lift the lower edge using a plastic opening tool.
  • Depending from the model it might help, when you first pry off the coffee spout. (See next step)
  • Unfold each of the side panels upwards and remove them.

The two colored side panels are only snapped into place. However, the latches sit very tight. You really need a lot of force. First lift the lower edge using a plastic opening tool.

Depending from the model it might help, when you first pry off the coffee spout. (See next step)

Unfold each of the side panels upwards and remove them.

Step 9

  • Insert a opening tool in the gap on the bottom of the coffee spout. Pry it off carefully.

Insert a opening tool in the gap on the bottom of the coffee spout. Pry it off carefully.

Step 10

              Brewing unit
  • Get the wires out of their holder.

Get the wires out of their holder.

Step 11

  • The plastic cover over the brewing unit is secured by two clips on each side. Use a metal spudger to pry them off.
  • Lift the cover slightly, but don’t remove it, it is still connected by some cables.

The plastic cover over the brewing unit is secured by two clips on each side. Use a metal spudger to pry them off.

Lift the cover slightly, but don’t remove it, it is still connected by some cables.

Step 12

  • Open the lever and lift the cover out over the lever. Make sure that the cables are not strained too much.
  • Put the cover aside, but leave the cables connected.

Open the lever and lift the cover out over the lever. Make sure that the cables are not strained too much.

Put the cover aside, but leave the cables connected.

Step 13

  • Use a metal spudger and insert it into the seam between the inner coffee spout and the brewing unit. Pry off the coffee spout.
  • Remove the inner coffee spout.

Use a metal spudger and insert it into the seam between the inner coffee spout and the brewing unit. Pry off the coffee spout.

Remove the inner coffee spout.

Step 14

  • Use a Torx T10 screwdriver to remove the four screws securing the brewing unit.

Use a Torx T10 screwdriver to remove the four screws securing the brewing unit.

Step 15

  • The brewing unit now remains only attached to the hot water hose. Use the metal spudger to pull out the metal clip at the end of the hose.
  • Pull out the end of the hot water hose.

The brewing unit now remains only attached to the hot water hose. Use the metal spudger to pull out the metal clip at the end of the hose.

Pull out the end of the hot water hose.

Step 16

  • Lift the brewing unit from the device.

Lift the brewing unit from the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.                                             


        VauWeh is helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

VauWeh

Author

                                      with 1 other contributor 


                    VauWeh

Member since: 10/19/2015

160,518 Reputation

                                      211 Guides authored                  



                       Badges:
                       41







                                                        +38 more badges

klausi.lindner - Aug 18, 2022

Reply

Hallo schönen guten Tag ich habe Problem mit meine Gran Maestria Espressomaschine… habe einen neuen Brühkopf eingebaut wie komme ich an den Wasserschlauch in der Maschine..mfg

Hallo ich habe Problem mit meinen Nespresso-Maschine gran Maestria.. habe den Brühkopf neu ausgetauscht wie komme ich an den Wasserschlauch dran