Difficulty

Moderate

Steps

7

Time Required

                          20 - 30 minutes

Sections

2

  • Shell
  • 6 steps
  • Trigger
  • 1 step

Flags

1

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackNerf Recon CS-6

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Remove Magazine
  • Skip this step if magazine is already removed.
  • Pull slide back.
  • Pull backwards on release buttons and slide magazine out.
  • Push slide back forward and pull trigger.

Skip this step if magazine is already removed.

Pull slide back.

Pull backwards on release buttons and slide magazine out.

Push slide back forward and pull trigger.

1024

Step 2

              Remove Visible Screws
  • Use the Phillips #0 Screwdriver to remove these 9 screws.
  • All screws marked in red are 9.6 mm Phillips #0 screws.
  • Note that left most screw is longer than the rest and is a 18.6 mm Phillips #0 screw.

Use the Phillips #0 Screwdriver to remove these 9 screws.

All screws marked in red are 9.6 mm Phillips #0 screws.

Note that left most screw is longer than the rest and is a 18.6 mm Phillips #0 screw.

Step 3

              Remove Hidden Screws
  • Pull slide back to reveal more screws.
  • Remove these 2 screws.
  • Push slide forward.
  • Pull trigger to release compression of the main spring.
  • Screws are 9.6 mm Phillips #0.
  • Pulling the trigger will keep spring from launching out of the gun when the two halves are separated.

Pull slide back to reveal more screws.

Remove these 2 screws.

Push slide forward.

Pull trigger to release compression of the main spring.

Screws are 9.6 mm Phillips #0.

Pulling the trigger will keep spring from launching out of the gun when the two halves are separated.

Step 4

              Remove Plunger Cap
  • Remove the screws on the plunger cap.
  • Tug the plunger cap off.
  • Screws are 9.6 mm Phillips #0.

Remove the screws on the plunger cap.

Tug the plunger cap off.

Step 5

              Remove Slide Screws
  • Remove the 2 screws on the slide.
  • Screws are 9.6 mm Phillips #0.
  • Hold the two halves of the gun together to prevent any springs from launching out.

Remove the 2 screws on the slide.

Hold the two halves of the gun together to prevent any springs from launching out.

Step 6

              Split the Gun in Half
  • Pull the gun apart at the middle seam.
  • Watch for any springs that might launch out.

Pull the gun apart at the middle seam.

Watch for any springs that might launch out.

Step 7

              Remove Trigger
  • Lift trigger up out of the gun.
  • From here, the trigger or the trigger spring can be replaced.

Lift trigger up out of the gun.

From here, the trigger or the trigger spring can be replaced.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 2 other contributors 


                    Pam Ruffner

Member since: 10/20/2014

984 Reputation

                                      3 Guides authored                  



                       Badges:
                       12







                                                        +9 more badges

Team

                       Baylor, Team 8-14, Williams Fall 2014                        

                                                  Member of Baylor, Team 8-14, Williams Fall 2014 



                    BU-WILLIAMS-F14S8G14                     


                                            3 Members                     


                                            6 Guides authored