Difficulty
Easy
Steps
10
Time Required
25 - 30 minutes
Sections
3
- Shell
- 6 steps
- Main Spring
- 1 step
- Plunger
- 3 steps
Flags
0
BackNerf Recon CS-6
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Remove Magazine
- Skip this step if magazine is already removed.
- Pull slide back.
- Pull backwards on release buttons and slide magazine out.
- Push slide back forward and pull trigger.
Skip this step if magazine is already removed.
Pull slide back.
Pull backwards on release buttons and slide magazine out.
Push slide back forward and pull trigger.
1024
Step 2
Remove Visible Screws
- Use the Phillips #0 Screwdriver to remove these 9 screws.
- All screws marked in red are 9.6 mm Phillips #0 screws.
- Note that left most screw is longer than the rest and is a 18.6 mm Phillips #0 screw.
Use the Phillips #0 Screwdriver to remove these 9 screws.
All screws marked in red are 9.6 mm Phillips #0 screws.
Note that left most screw is longer than the rest and is a 18.6 mm Phillips #0 screw.
Step 3
Remove Hidden Screws
- Pull slide back to reveal more screws.
- Remove these 2 screws.
- Push slide forward.
- Pull trigger to release compression of the main spring.
- Screws are 9.6 mm Phillips #0.
- Pulling the trigger will keep spring from launching out of the gun when the two halves are separated.
Pull slide back to reveal more screws.
Remove these 2 screws.
Push slide forward.
Pull trigger to release compression of the main spring.
Screws are 9.6 mm Phillips #0.
Pulling the trigger will keep spring from launching out of the gun when the two halves are separated.
Step 4
Remove Plunger Cap
- Remove the screws on the plunger cap.
- Tug the plunger cap off.
- Screws are 9.6 mm Phillips #0.
Remove the screws on the plunger cap.
Tug the plunger cap off.
Step 5
Remove Slide Screws
- Remove the 2 screws on the slide.
- Screws are 9.6 mm Phillips #0.
- Hold the two halves of the gun together to prevent any springs from launching out.
Remove the 2 screws on the slide.
Hold the two halves of the gun together to prevent any springs from launching out.
Step 6
Split the Gun in Half
- Pull the gun apart at the middle seam.
- Watch for any springs that might launch out.
Pull the gun apart at the middle seam.
Watch for any springs that might launch out.
Step 7
Remove Spring
- Pull the spring out the back of the gun.
Pull the spring out the back of the gun.
Step 8
Removing Plunger Guide
- Lift the plunger guide straight up out of the gun.
Lift the plunger guide straight up out of the gun.
Step 9
Remove Plunger
- Pull the plunger out the back of the gun off of the inner piece.
Pull the plunger out the back of the gun off of the inner piece.
Step 10
Remove Other Half of Plunger
- Pull the remaining half of the plunger out the back of the gun.
Pull the remaining half of the plunger out the back of the gun.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 3 other contributors
Asad Qureshi
Member since: 10/22/2014
586 Reputation
3 Guides authored
Badges:
17
+14 more badges
Team
Baylor, Team 8-14, Williams Fall 2014
Member of Baylor, Team 8-14, Williams Fall 2014
BU-WILLIAMS-F14S8G14
3 Members
6 Guides authored
Angela Hirschi - Jan 27, 2018
Reply
Do you know anywhere that you can buy a replacement plunger? Thanks
