Difficulty

Difficult

Steps

10

Time Required

                          15 - 30 minutes

Sections

5

  • Blaster Casing
  • 3 steps
  • Battery
  • 2 steps
  • Laser Trigger
  • 1 step
  • Laser Assembly
  • 2 steps
  • LED
  • 2 steps

Flags

2

Grammar Police

Embrace your inner English teacher and help improve this guide’s grammar!

Step Trimmer

This guide has unnecessary steps. Trim them to be more concise!

  • BackNerf N-Strike Firestrike

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

The light is located at the center of the circuit board. Once all of these steps are taken you can remove the LED light.

What you need

Step 1

              Blaster Casing
  • Remove the seven 10-mm black Phillips screws from the blaster casing with a #1 Phillips Screwdriver.

Remove the seven 10-mm black Phillips screws from the blaster casing with a #1 Phillips Screwdriver.

1024

Step 2

  • Slowly pull apart the blaster casing, starting at the battery location.
  • Keep pulling apart slowly until it separates completely. Be cautious as to not send the internal components flying.

Slowly pull apart the blaster casing, starting at the battery location.

Keep pulling apart slowly until it separates completely. Be cautious as to not send the internal components flying.

Step 3

  • For reassembly, ensure that the chrome nut gets put back in the proper location, signified by the red box.
  • For reassembly, ensure that all the parts are lined up correctly on the dowels, signified by the four orange boxes.
  • For reassembly, note the location of the springs as highlighted in the second photo.

For reassembly, ensure that the chrome nut gets put back in the proper location, signified by the red box.

For reassembly, ensure that all the parts are lined up correctly on the dowels, signified by the four orange boxes.

For reassembly, note the location of the springs as highlighted in the second photo.

Step 4

              Remove battery cover
  • Use a #1 Phillips screwdriver to remove the 10 -mm screw that secures the battery plate, then remove the battery cover using your hands.

Use a #1 Phillips screwdriver to remove the 10 -mm screw that secures the battery plate, then remove the battery cover using your hands.

Step 5

  • Slide out the two AAA batteries using your fingers.

Slide out the two AAA batteries using your fingers.

Step 6

              Laser Trigger
  • Remove the laser trigger by grabbing the trigger with your fingers and pulling it up and out.

Remove the laser trigger by grabbing the trigger with your fingers and pulling it up and out.

Step 7

              Laser Assembly
  • Gently pull up on the circuit board located near the gun handle until it separates from the gun.
  • The wire that attaches to the circuit board is also attached to the laser. Be careful not to use excessive force and damage or disconnect the wire.

Gently pull up on the circuit board located near the gun handle until it separates from the gun.

The wire that attaches to the circuit board is also attached to the laser. Be careful not to use excessive force and damage or disconnect the wire.

Step 8

  • Grip the circuit board located at the base of the laser with your fingers; rotate it towards the ammo compartment on the blaster until the guide hole is clear of the guide pin.
  • Slide the laser assembly out.

Grip the circuit board located at the base of the laser with your fingers; rotate it towards the ammo compartment on the blaster until the guide hole is clear of the guide pin.

Slide the laser assembly out.

Step 9

              LED
  • Pinch the clips holding the laser beam casing to the circuit board with your fingers. Slide off the casing revealing the LED.

Pinch the clips holding the laser beam casing to the circuit board with your fingers. Slide off the casing revealing the LED.

Step 10

  • Use a soldering iron to heat up the two connections holding the LED to the circuit board. Remove the LED.

Use a soldering iron to heat up the two connections holding the LED to the circuit board. Remove the LED.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      6 other people completed this guide.

Author

                                      with 4 other contributors 


                    Hayes Kimball

Member since: 04/19/2015

742 Reputation

                                      5 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       Cal Poly, Team 15-6, Amido Spring 2015                        

                                                  Member of Cal Poly, Team 15-6, Amido Spring 2015 



                    CPSU-AMIDO-S15S15G6                     


                                            3 Members                     


                                            8 Guides authored