Difficulty
Moderate
Steps
7
Time Required
Suggest a time??
Sections
2
- Outer Shell
- 5 steps
- Trigger Mechanism
- 2 steps
Flags
1
Better Introduction
Improve this guide by completing or revising its introduction.
BackNerf N-Strike Elite Strongarm
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Outer Shell
- Lay the Nerf Strongarm on its side, left side facing up.
Lay the Nerf Strongarm on its side, left side facing up.
1024
Step 2
- Locate the 12 Philips head screws and remove them: Head Diameter= 4.3mm, Thread Pitch= 1mm, Screw Length= 8mm
Locate the 12 Philips head screws and remove them: Head Diameter= 4.3mm, Thread Pitch= 1mm, Screw Length= 8mm
Step 3
- Before removing the cover, make sure to first remove the cover for the cocking mechanism. The top half is freely removable.
- The other half of the cocking mechanism is connected with a spring which may slide off the blaster. Be advised this is normal but worth watching to avoid damaging the spring.
Before removing the cover, make sure to first remove the cover for the cocking mechanism. The top half is freely removable.
The other half of the cocking mechanism is connected with a spring which may slide off the blaster. Be advised this is normal but worth watching to avoid damaging the spring.
Step 4
- At this time, remove the blaster cover to reveal its internals.
- If the blaster is resting on its side, the barrel may shift slightly as it is leaning on itself (seen in the image). This is normal but should be handled with care to keep the blaster together.
At this time, remove the blaster cover to reveal its internals.
If the blaster is resting on its side, the barrel may shift slightly as it is leaning on itself (seen in the image). This is normal but should be handled with care to keep the blaster together.
Step 5
- Once the screws have been removed, lift the top half of the gun off.
- Notice, the gray colored piece must be removed first in order for the larger half to be removed.
- Take care and try not to lose any smaller pieces as you open it up.
- Locking tab for attachments.
Once the screws have been removed, lift the top half of the gun off.
Notice, the gray colored piece must be removed first in order for the larger half to be removed.
Take care and try not to lose any smaller pieces as you open it up.
Locking tab for attachments.
Step 6
Trigger Mechanism
- Locate the trigger mechanism’s assembly, and notice that it’s held in place by a single philip’s head screw. Remove it.
- Screw specifications: Philips head, Head Diameter= 4.3mm, Thread Pitch= 1mm, Screw Length= 8mm
Locate the trigger mechanism’s assembly, and notice that it’s held in place by a single philip’s head screw. Remove it.
Screw specifications: Philips head, Head Diameter= 4.3mm, Thread Pitch= 1mm, Screw Length= 8mm
Step 7
- Inspect the orange parts for signs of damage and debris. Any broken pieces must be replaced.
- This is the spring that controls the trigger. Through regular use, the spring may become mangled or damaged. If it becomes damaged, a spring from a ballpoint pen can function as a decent replacement.
Inspect the orange parts for signs of damage and debris. Any broken pieces must be replaced.
This is the spring that controls the trigger. Through regular use, the spring may become mangled or damaged. If it becomes damaged, a spring from a ballpoint pen can function as a decent replacement.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
6 other people completed this guide.
Author
with 4 other contributors
Alexander Kim
Member since: 08/27/2015
793 Reputation
3 Guides authored
Badges:
14
+11 more badges
Team
USF Tampa, Team 5-4, Blackwell Fall 2015
Member of USF Tampa, Team 5-4, Blackwell Fall 2015
USFT-BLACKWELL-F15S5G4
4 Members
12 Guides authored
