Difficulty
Moderate
Steps
12
Time Required
3 minutes
Sections
2
- Outer Shell
- 5 steps
- Spring Piston Chamber
- 7 steps
Flags
0
BackNerf N-Strike Elite Strongarm
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Outer Shell
- Lay the Nerf Strongarm on its side, left side facing up.
Lay the Nerf Strongarm on its side, left side facing up.
1024
Step 2
- Locate the 12 Philips head screws and remove them: Head Diameter= 4.3mm, Thread Pitch= 1mm, Screw Length= 8mm
Locate the 12 Philips head screws and remove them: Head Diameter= 4.3mm, Thread Pitch= 1mm, Screw Length= 8mm
Step 3
- Before removing the cover, make sure to first remove the cover for the cocking mechanism. The top half is freely removable.
- The other half of the cocking mechanism is connected with a spring which may slide off the blaster. Be advised this is normal but worth watching to avoid damaging the spring.
Before removing the cover, make sure to first remove the cover for the cocking mechanism. The top half is freely removable.
The other half of the cocking mechanism is connected with a spring which may slide off the blaster. Be advised this is normal but worth watching to avoid damaging the spring.
Step 4
- At this time, remove the blaster cover to reveal its internals.
- If the blaster is resting on its side, the barrel may shift slightly as it is leaning on itself (seen in the image). This is normal but should be handled with care to keep the blaster together.
At this time, remove the blaster cover to reveal its internals.
If the blaster is resting on its side, the barrel may shift slightly as it is leaning on itself (seen in the image). This is normal but should be handled with care to keep the blaster together.
Step 5
- Once the screws have been removed, lift the top half of the gun off.
- Notice, the gray colored piece must be removed first in order for the larger half to be removed.
- Take care and try not to lose any smaller pieces as you open it up.
- Locking tab for attachments.
Once the screws have been removed, lift the top half of the gun off.
Notice, the gray colored piece must be removed first in order for the larger half to be removed.
Take care and try not to lose any smaller pieces as you open it up.
Locking tab for attachments.
Step 6
Spring Piston Chamber
- First, remove the outer parts of the blaster, starting with the top part of the cocking mechanism. Then remove the full cover itself.
First, remove the outer parts of the blaster, starting with the top part of the cocking mechanism. Then remove the full cover itself.
Step 7
- Remove the barrel and the front part of the blaster. The components should simply slide off.
Remove the barrel and the front part of the blaster. The components should simply slide off.
Step 8
- Remove the screw on the inside of the gun.
- Screw specifications: Philips head, Head Diameter= 4.3mm, Thread Pitch= 1mm, Screw Length= 8mm
Remove the screw on the inside of the gun.
Screw specifications: Philips head, Head Diameter= 4.3mm, Thread Pitch= 1mm, Screw Length= 8mm
Step 9
- Remove the trigger, the cocking holdback, and the air compressor chamber
Remove the trigger, the cocking holdback, and the air compressor chamber
Step 10
- Remove the spring holding the air compressor together.
Remove the spring holding the air compressor together.
Step 11
- Remove the spring air compressor component.
Remove the spring air compressor component.
Step 12
- This is the spring that controls the air compressor. If it is damaged you have found your problem. Replace this spring and the blaster should work.
This is the spring that controls the air compressor. If it is damaged you have found your problem. Replace this spring and the blaster should work.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
7 other people completed this guide.
Author
with 5 other contributors
Dylan Cooper Dalrymple
Member since: 01/15/2015
735 Reputation
3 Guides authored
Badges:
17
+14 more badges
Team
USF Tampa, Team 5-4, Blackwell Fall 2015
Member of USF Tampa, Team 5-4, Blackwell Fall 2015
USFT-BLACKWELL-F15S5G4
4 Members
12 Guides authored
juanestebanlopezcastrillon - Feb 5, 2017
Reply
mi nerf strongarm no dispara los dardos con la misma potencia que cuando la utilice por primera vez, dispara los dardos demasiado suave
Álvaro Sousa PT - Apr 7, 2019
Maybe the problem is the dards.
Skm - Jul 1, 2017
Reply
My nerf elite disruptor’s drum some times working but sometimes notworkin
JoseRafael - Jun 1, 2018
Reply
what is the size of the spring?