Nerf N Strike Elite Strongarm Barrel Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

Outer Shell
5 steps
Barrel
5 steps

Flags

BackNerf N-Strike Elite Strongarm
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Outer Shell

Lay the Nerf Strongarm on its side, left side facing up.

Lay the Nerf Strongarm on its side, left side facing up.

1024

Step 2

Locate the 12 Philips head screws and remove them: Head Diameter= 4.3mm, Thread Pitch= 1mm, Screw Length= 8mm

Locate the 12 Philips head screws and remove them: Head Diameter= 4.3mm, Thread Pitch= 1mm, Screw Length= 8mm

Step 3

Before removing the cover, make sure to first remove the cover for the cocking mechanism. The top half is freely removable.
The other half of the cocking mechanism is connected with a spring which may slide off the blaster. Be advised this is normal but worth watching to avoid damaging the spring.

Before removing the cover, make sure to first remove the cover for the cocking mechanism. The top half is freely removable.

The other half of the cocking mechanism is connected with a spring which may slide off the blaster. Be advised this is normal but worth watching to avoid damaging the spring.

Step 4

At this time, remove the blaster cover to reveal its internals.
If the blaster is resting on its side, the barrel may shift slightly as it is leaning on itself (seen in the image). This is normal but should be handled with care to keep the blaster together.

At this time, remove the blaster cover to reveal its internals.

If the blaster is resting on its side, the barrel may shift slightly as it is leaning on itself (seen in the image). This is normal but should be handled with care to keep the blaster together.

Step 5

Once the screws have been removed, lift the top half of the gun off.
Notice, the gray colored piece must be removed first in order for the larger half to be removed.
Take care and try not to lose any smaller pieces as you open it up.
Locking tab for attachments.

Once the screws have been removed, lift the top half of the gun off.

Notice, the gray colored piece must be removed first in order for the larger half to be removed.

Take care and try not to lose any smaller pieces as you open it up.

Locking tab for attachments.

Step 6

              Barrel

Start by inspecting the barrel closer for broken components.
Pressing the unloading button is a good test to check if the barrel will rotate out.
If the barrel fails to cooperate, continue onto the next steps.

Start by inspecting the barrel closer for broken components.

Pressing the unloading button is a good test to check if the barrel will rotate out.

If the barrel fails to cooperate, continue onto the next steps.

Step 7

Once the cover is off, the barrel component will be free and removable.

Once the cover is off, the barrel component will be free and removable.

Step 8

Once the barrel is removed, continue by removing the front shaft. This component is also independent of the blaster and does not require tools.

Once the barrel is removed, continue by removing the front shaft. This component is also independent of the blaster and does not require tools.

Step 9

Look for any signs of debris or any damaged locations that may be causing the barrel to lock.

Look for any signs of debris or any damaged locations that may be causing the barrel to lock.

Step 10

At this time, all components interacting with the barrel are removed.
Take this time to inspect the barrel for any signs of debris or damaged locations.

At this time, all components interacting with the barrel are removed.

Take this time to inspect the barrel for any signs of debris or damaged locations.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      9 other people completed this guide.

Author

                                      with 3 other contributors

                    Alexander Kim

Member since: 08/27/2015

793 Reputation

                                      3 Guides authored                  



                       Badges:
                       14







                                                        +11 more badges

Team

                       USF Tampa, Team 5-4, Blackwell Fall 2015                        

                                                  Member of USF Tampa, Team 5-4, Blackwell Fall 2015 



                    USFT-BLACKWELL-F15S5G4                     


                                            4 Members                     


                                            12 Guides authored

cryo17 - Aug 23, 2019

hi my barrel keeps ritating and is not fixed and does not stay aligned to the shooting point what shall i do

Introduction#

What you need#

Team#

Introduction

What you need

Team