Nerf N Strike Elite Hail Fire Inner Plastic Components Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 - 30 minutes

Sections

Left Shell
12 steps
Inner Plastic Components
4 steps

Flags

Missing Prerequisites

This guide is missing information on how to start the process. Make a prerequisite guide!

Better Introduction

Improve this guide by completing or revising its introduction.

BackNerf N-Strike Elite Hail-Fire
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Left Shell

Before disassembling your Nerf Hail-Fire, be sure to remove the batteries.
Remove the two 9.0 mm Phillips screws securing the battery compartment.
Slide the battery compartment out.

Before disassembling your Nerf Hail-Fire, be sure to remove the batteries.

Remove the two 9.0 mm Phillips screws securing the battery compartment.

Slide the battery compartment out.

1024

Step 2

Remove the five 9.0 mm Phillips screws securing the trigger.

Remove the five 9.0 mm Phillips screws securing the trigger.

Step 3

Remove the single 11.0 mm Phillips screw securing the magazine cartridge chambers.
Pull the entire chamber upwards to separate it from the rest of the Nerf Gun.

Remove the single 11.0 mm Phillips screw securing the magazine cartridge chambers.

Pull the entire chamber upwards to separate it from the rest of the Nerf Gun.

Step 4

Remove both halves of the ring by tugging on it upwards until the lock gets freed.
This requires quite a bit of force and if you are not careful, you may break the plastic lock.

Remove both halves of the ring by tugging on it upwards until the lock gets freed.

This requires quite a bit of force and if you are not careful, you may break the plastic lock.

Step 5

Remove the four 9.0 mm Phillips screws from the newly revealed cylinder.

Remove the four 9.0 mm Phillips screws from the newly revealed cylinder.

Step 6

Remove the three 9.0 mm Phillips screws holding the top latch of the Nerf Gun together.

Remove the three 9.0 mm Phillips screws holding the top latch of the Nerf Gun together.

Step 7

Remove the three 9.0 mm Phillips screws holding together the firing chamber.
Remove the single 7.0 mm Phillips screw below the barrel.
Remove the two 14.0 mm Philips screws using a screwdriver with a length of approximately 4.0 inches and a diameter of approximately 0.2 cm.

Remove the three 9.0 mm Phillips screws holding together the firing chamber.

Remove the single 7.0 mm Phillips screw below the barrel.

Remove the two 14.0 mm Philips screws using a screwdriver with a length of approximately 4.0 inches and a diameter of approximately 0.2 cm.

Step 8

Remove the single 14.0 mm Phillips screw holding together the handle and the Nerf Gun.

Remove the single 14.0 mm Phillips screw holding together the handle and the Nerf Gun.

Step 9

Remove the two 9.0 mm Phillips screws holding together the handle.
Remove the plastic cover of the handle.

Remove the two 9.0 mm Phillips screws holding together the handle.

Remove the plastic cover of the handle.

Step 10

Insert one plastic opening tool inside one side of the orange part depicted in the picture.
Insert a second plastic opening tool to the other side of the orange part and gradually pull the piece out, freeing it from the handle.

Insert one plastic opening tool inside one side of the orange part depicted in the picture.

Insert a second plastic opening tool to the other side of the orange part and gradually pull the piece out, freeing it from the handle.

Step 11

Pull one end of the handle away from the orange latch.
Repeat the procedure on the other side to completely remove the handle from the rest of the Nerf Gun.

Pull one end of the handle away from the orange latch.

Repeat the procedure on the other side to completely remove the handle from the rest of the Nerf Gun.

Step 12

Lift the entire left shell slowly. The process should be easy and if there is any resistance, there is something wrong. You may have forgotten a screw.
Completely remove the left shell from the rest of the Nerf Gun.

Lift the entire left shell slowly. The process should be easy and if there is any resistance, there is something wrong. You may have forgotten a screw.

Completely remove the left shell from the rest of the Nerf Gun.

Step 13

              Inner Plastic Components

Remove the cartridge support.

Remove the cartridge support.

Step 14

Remove the handle crank.

Remove the handle crank.

Step 15

Remove the clear plastic barrel cover.

Remove the clear plastic barrel cover.

Step 16

Remove the firing pin.

Remove the firing pin.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 3 other contributors

                    sage

Member since: 01/24/2014

301 Reputation

                                      3 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Cal Poly, Team 13-13, Regan Winter 2014                        

                                                  Member of Cal Poly, Team 13-13, Regan Winter 2014 



                    CPSU-REGAN-W14S13G13                     


                                            4 Members                     


                                            7 Guides authored

Missing Prerequisites#

Better Introduction#

Introduction#

What you need#

Team#

Missing Prerequisites

Better Introduction

Introduction

What you need

Team